Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

secam7
Posty: 60
Rejestracja: 5 września 2011, o 19:21

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: secam7 »

To z pilotem, mniejszy problem, choć dziwny, firmware raczej powinien być przystosowany do kilku różnych pilotów,
szczególnie w dzisiejszych czasach, gdy wszystkiego brakuje. :(

Mam proste pytanie:
Czy ktoś używa tego firmware na wiwie (jakiejś) i działa mu odtwarzanie plików multimedialnych?
Ja mam zwykły plik mp4 (h264) i w sekcji "Filmy" go widać, ale jest błąd odtwarzania. :(

ukaszu
Posty: 73
Rejestracja: 15 września 2022, o 10:55
Miejscowość: Zalesie

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: ukaszu »

MaxEvans pisze: 30 września 2022, o 19:25 Da się coś z tym zrobić ?
Bez starego sprzętu ciężko jest mi pomóc. To może być kwestia tego jak rozwiązany jest dostęp do internetu - np. nowy firmware może widzieć network adapter i zakładać że to dongle od wifi (a to przecież ethernet). Jestem przekonany że w konsoli jest jakiś komunikat który pozwalałby to namierzyć, ale trzeba by się było tam podłączyć.

Co do brakujących przycisków to mapowanie przeniosłem skryptem tłumaczącym z FW Wiwy (żeby nie popełnić błędu przy ręcznej analizie) tak jak oczekuje tego FW Signala, nie zwracałem uwagi na brakujące przyciski bo docelowy użytkownik z nich i tak nie korzysta (w moim przypadku). W wolnej chwili zobaczę czego brakuje, ale najpierw testy z Arivą.

MaxEvans
Posty: 1185
Rejestracja: 13 listopada 2016, o 09:49
Miejscowość: Tuszyn
Odbiornik: LG Flatron M237WDP-PZ ARIVA T75 SKYMASTER STB265 WIWA LITE
Instalacja antenowa: Antena DIPOL 11 Symetryzator Kabel Televes T-100 Plus 5 m
Nadajnik - obiekt nadawczy: SLR Dąbrowa (22 km) RTCN Zygry (43 km)

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: MaxEvans »

Ok dziękuję

Zygzuś
Posty: 134
Rejestracja: 22 maja 2022, o 13:25
Miejscowość: Tarnów
Odbiornik: Wiwa Maxx
Nadajnik - obiekt nadawczy: RTON G.Św.Marcina

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: Zygzuś »

secam7 pisze: 30 września 2022, o 22:08 To z pilotem, mniejszy problem, choć dziwny, firmware raczej powinien być przystosowany do kilku różnych pilotów,
szczególnie w dzisiejszych czasach, gdy wszystkiego brakuje. :(
W wiwie jest kilka wersji pilota i zmapowane są te przyciski podobnie, choć w tym największym nie ma podwójnych +vol- i +ch-
Teraz już sprawdziłem, że w tym zmodowanym sofcie przyciski są źle zmapowane, kolorowe zamienione na rewind forward stop play.

ukaszu
Posty: 73
Rejestracja: 15 września 2022, o 10:55
Miejscowość: Zalesie

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: ukaszu »

W MC-006 czerwony to Play/Pause, zielony to Stop, żółty to REV, a niebieski to FFD. W tabeli mapowania natomiast wszystkie kolorowe przyciski są wpisane dwa razy (dla dwóch różnych komend), a funkcja mapująca pobiera pierwszy znaleziony. Ogólnie bałagan.

Na pilocie MC-006 zdublowane są też przyciski V+, V-, CH+, CH- - fizycznie jest 8 przycisków, ale mają parami taki same kody (czyli kody są tylko 4). Również bałagan.

gocom
Posty: 94
Rejestracja: 6 lutego 2022, o 17:24
Miejscowość: RU
Odbiornik: WIWA H265 MAXX, Vmade K5, Vmade K6 AV.

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: gocom »

@ukaszu
Prefiks Vmade K6 zachowuje się z oprogramowaniem Signal w taki sam sposób jak MaxEvans Wiwa lite eth.
Dzienniki:

Dziennik włączania dekodera Vmade K6 z oprogramowaniem WIWA PRO

Kod: Zaznacz cały

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Dec 26 2019 - 17:32:16)  MBOT-1106.0.10.936a0fd.201806111716


DRAM:
Hello U-Boot
Stack Pointer at: 83620740
mem initial, start 0x82CEE180, len 0x402000
SPI:  Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In:    serial
Out:   serial
Err:   serial
[ERROR] do_spi_init_partition:1218: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'

>>>>>>>>>>>>>>>>>>>>Start bootlogo
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showboot.................
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x3A000 0x400
offset 0x3A000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3A028 0x342516; LzmaDec 0x80B00000 0x342516 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
============= set bootargs ===============
Hit any key to stop autoboot:  0
enable dont overwrite function
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x35FD000
[USB] Reg 0x28: 0xD000 0x35F
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /SbootUpgrade.bin

** Unable to read "/SbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /MbootUpgrade.bin

** Unable to read "/MbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /UrsaUpgrade.bin

** Unable to read "/UrsaUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
warn!! no upgrade file in usb.
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
usb -

Usage:
usb
offset 0x3A028, size 0x342516

LZMA Decompression...buf data channge
CRC check success !!
ok
disable interrupts
## Starting application at 0x80000224 ...
1999 drvEMAC_GetMacAddr
cyg_if_attach.225 - After initialize list 0x806a80ac
IFP: 0x806a809c (eth0)
cyg_if_attach.290 - After inserting 0x80957c20 into list 0x806a80ac
IFP: 0x806a809c (eth0)
IFA: 0x80957c20 - <<0x80957c9c>>
===> rt_ecos_init()
cyg_if_attach.225 - After initialize list 0x807566c0
IFP: 0x807566b0 (ra0)
cyg_if_attach.290 - After inserting 0x80957b20 into list 0x807566c0
IFP: 0x807566b0 (ra0)
IFA: 0x80957b20 - <<0x80957b9c>>
cyg_if_attach.225 - After initialize list 0x80a0e4b4
IFP: 0x80a0e4a4 (lo0)
cyg_if_attach.290 - After inserting 0x80957a20 into list 0x80a0e4b4
IFP: 0x80a0e4a4 (lo0)
IFA: 0x80957a20 - <<0x80957a9c>>
Register_netisr [2] fun=0x800f6455

[eCos][CPU INFO] : CPU Clock = 750000000 : RTC Period = 375000
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[eCos] UtopiaInit

shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
[SYS][ERR][AESDMARegisterToUtopia:2302] Not support AESDMA
1762 MDrv_EMAC_Init 17:36:18 Aug 28 2018
1777 MDrv_EMAC_Init RX_BUFFER_BASE:80824000
1779 MDrv_EMAC_Init RBQP_BASE:80844000
1781 MDrv_EMAC_Init TX_BUFFER_BASE:80844200
1785 MDrv_EMAC_Init dlist:a0844000
1786 MDrv_EMAC_Init emac addr:a0820614,20000000,80824000,80844000
1789 MDrv_EMAC_Init  _VerEMAC_Task[0].pStack:0x80850614
Flash is detected (0x0D00, 0x5E, 0x40, 0x16)

0046119500d0
Auth OK
0650 DefaultCfgEMAC initedEMAC=0, connected=0, flagMacTxPermit=0
1129 InitializeEMAC config2_Value=0xf001
1085 MDev_EMAC_ScanPhyAddr [ PHY Addr ] ==> :0 BMSR = 000078c9
1088 MDev_EMAC_ScanPhyAddr [ PHY Addr ] ==> :0
RBQP_BASE=80844000
RX_DESC_NUMBER=64
1186 InitializeEMAC RX_CHECKSUM
1191 InitializeEMAC RX_DESC_MODE
1200 InitializeEMAC config3_Value=0xf
1213 InitializeEMAC uNegPhyVal=2
1225 InitializeEMAC initedEMAC=0, connected=0, flagMacTxPermit=1, duplex2
1242 InitializeEMAC ETH_CFG finish
1252 InitializeEMAC MDev_EMAC_update_linkspeed finish ret=-1
1267 InitializeEMAC  MHal_EMAC_Write_IER
1273 InitializeEMAC  MHal_EMAC_Write_IER finish
1285 InitializeEMAC initedEMAC=1, connected=0, flagMacTxPermit=1
1750 _DrvEMAC_Task0 EMAC: init done
 <FWTSP> : RASP from TSIF_RASP
Mstar USB initial, 4 ports>> FwVersion:002F2600 , Date:20140924
[FUNC MApi_DB_DFT_GetPCHIntf_CT] [pstIntf  0x8040a070]
 supported
[NCM] The allocted address is 0xa2f9eff0
Init Software Timer ok
usbcore: regtered new driver hub
[USB] quirk list init, support max 20
usbcore: regtered new driver usb-storage
[USB] MS USB Host Lib for K5AP only


rtusb init rt2870 --->


usbcore: regtered new driver rt2870
Init chip K5AP, port 0
[USB] constant upll NLib,[MApp_CheckFlash][1730] s8SN0 = 1
[CreatDTVProgramIndexTableAndProgramIDTable,6389] DTV Data Structure is valid

[[utopia]]      Start HAL_AUDIO_AllocateVars InitShmFlag=0
create Audio SHM data ...
Audio SHM data is created
reset Audio SHM data ...
[[utopia]][audio]      MStar AUDIO Driver Version : 2.2.3
[[utopia]]      Start HAL_AUDIO_AllocateVars InitShmFlag=1
[[utopia]]      HAL_AUDIO_AllocateVars QUERY ClientCounter=1
[[utopia]]      MDrv_AUDIO_PCM_Init: Init PCM device
[SYS][ERR][_SysInit_GetColorFMTCMD:1067] fail to get color format failed!!
MDrv_PNL_Init u32PnlRiuBaseAddr = bf200000
MDrv_PNL_Init u32PMRiuBaseAddr = bf000000
[XC,Version] 00709801
  UTMI base 0xbf20no need to patch
7500, USBC base 0xbf200e00, UHC base 0xbf204800, USBBC base 0xbf226e00
[USB] init squelch level 0x2
ehci_hcd (CPE_AMBA) at 0x0xbf204800, irq 7
new USB Bus, assigned pBus number 1
pQh: 0xa2f9f000, pQh->qh_dma_addr: 0x02f9f000
periodic frame list array 0xa2fa1000, size 1024
[EHCI] Enable Park Mode: 3
EHCI 1.00, driver eCos Newhost
[root hub] device address 1
USB device manufacturer string (index 3) = MStar eCos 1.0 ehci_hcd
USB device product string (index 2) = CPE_AMBA EHCI
USB device serial number string (index 1) = cpe_ehci
usbdev 1-0 - registering interface 1-0:0
USB hub found
1 port detected

Usb start EX..., pRootHub = 806e97f8

UTask EX>> ... port 0 starting
[FUNC MApi_ChanScan_Init] [LINE 836] MsOS_CreateTask ChScan_Task
drv_frontend_index = 0 u32BroadcastType = 2
=========================== Broadcast Type List ==========================
 0x0 -> BROADCAST_TYPE_NOT_SEETING
 0x1 -> DVBC
 0x2 -> DVBT
 0x3 -> DVBT2
 0x4 -> ISDBT
 0x5 -> DVBS
 0x6 -> ATSC
 0x7 -> J83B
 0xa -> DTMB
 0xb -> DVBS2
 0xf -> DSS
 0x10 -> ATV_PAL
 0x11 -> ATV_SECAM_L_PRIME
 0x12 -> ATV_NTSC
========================== End Broadcast Type List =======================
MDrv_IIC_Init  PORT  1
MDrv_IIC_InitPort1: OK
MDrv_IIC_Init  PORT  1
MDrv_IIC_InitPort1: OK
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A918 1B0 0 0 80228C17 0>
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A92C 1C7 0 0 80228C59 0>
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A918 1B0 0 0 80228C17 0>
Request extension function (14) does not exist
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A918 1B0 808FF17 808FF18 80228C17 808FF1A>
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A92C 1C7 808FF17 808FF18 80228C59 808FF1A>
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A918 1B0 808FF17 808FF18 80228C17 808FF1A>MDrv_HDMITx_EdidChecking::block 0 ==>
0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x10, 0xAC, 0x48, 0xF0, 0x4C, 0x37, 0x54, 0x41,
0x23, 0x18, 0x01, 0x03, 0x80, 0x34, 0x20, 0x78, 0xEA, 0x1D, 0xF5, 0xAE, 0x4F, 0x35, 0xB3, 0x25,
0x0D, 0x50, 0x54, 0xA5, 0x4B, 0x00, 0x81, 0x80, 0xA9, 0x40, 0xD1, 0x00, 0x71, 0x4F, 0x01, 0x01,
0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3C, 0x80, 0xA0, 0x70, 0xB0, 0x23, 0x40, 0x30, 0x20,
0x36, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1A, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x38, 0x34, 0x4B,
0x39, 0x36, 0x34, 0x38, 0x51, 0x41, 0x54, 0x37, 0x4C, 0x0A, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x44,
0x45, 0x4C, 0x4C, 0x20, 0x55, 0x32, 0x34, 0x31, 0x33, 0x0A, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD,
0x00, 0x38, 0x4C, 0x1E, 0x51, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xBD,

MDrv_HDMITx_EdidChecking::Extension Block Number = 1
MDrv_HDMITx_EdidChecking::Block #1
0x02, 0x03, 0x25, 0xF1, 0x50, 0x90, 0x05, 0x04, 0x03, 0x02, 0x07, 0x16, 0x01, 0x1F, 0x12, 0x13,
0x14, 0x20, 0x15, 0x11, 0x06, 0x23, 0x09, 0x1F, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38,
0x2D, 0x83, 0x01, 0x00, 0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45,
0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58,
0x2C, 0x25, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x9E, 0x01, 0x1D, 0x00, 0x72, 0x51, 0xD0, 0x1E,
0x20, 0x6E, 0x28, 0x55, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x8C, 0x0A, 0xD0, 0x8A, 0x20,
0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16,

_MDrv_HDMITx_ParseCEAExtEdid::Short Video Block: 16
_MDrv_HDMITx_ParseCEAExtEdid::Short Audio Block:3
_MDrv_HDMITx_ParseCEAExtEdid::VSDB
Physcal Address = [1, 0, 0, 0]
_MDrv_HDMITx_ParseHdmiVSDB::Support AI = 0 !
_MDrv_HDMITx_ParseDeepColorInfo::Support Color Depth 36-bit
DAC eTiming =6
DAC Panel Table Index =6

UTask EX>> USB Port 0 is connected
Request extension function (a) does not exist
=====================================================================================================
[SYS][ERR][_SysInit_GetPanelCMD:1046] fail to get panel failed!!
Wait V Sync!!
[FrontEnd_Index 0]  Demod: DEMOD_MSINTERN_DVBT2     Tuner: TUNER_R836               I2C_Port:HW_I2C0
=====================================================================================================
MDrv_IIC_Init  PORT  1
MDrv_IIC_InitPort1: OK
MDrv_IIC_Init  PORT  1
MDrv_IIC_InitPort1: OK
Request extension function (6) does not exist
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A918 1B0 0 807FEB14 80228C17 0>
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A92C 1C7 0 807FEB14 80228C59 0>
<Bad format string: 803F6628 : 805921D8 8059A89C 8059A918 1B0 0 807FEB14 80228C17 0>
<saved irq> portsc[0x 803], usbcmd[10b08]
hub_port_connect[Hal_VE_EnableDI][1841] bEnable = 0, bIsDNR2VE = 0
_change ===20180329===> port 1, status 1, change 1
MApi_VectorFont_Init total size=1310720, free size=1154400, large size=1154212

 0
...[MApp_ZUI_API_GetLanguageNum, 163] u8LanguageNum = 8...
stSysSetting.LedDimmer =8
RootHub SPEED: high-speed
:: Device Speed is 480 Mb/s
new USB device on path usb:1, assigned address 2
pQh: 0xa2f9f060, pQh->qh_dma_addr: 0x02f9f060
usb new device VID = 23a9, PID = ef18
USB device manufacturer string (index 1) = USB
USB device product string (index 2) = DISK
usbdev 1-1 - registering interface 1-1:0
find USB MSC device at device number 2
<saved irq> portsc[0x   d], usbcmd[10b09]
pQh: 0xa2f9f0c0, pQh->qh_dma_addr: 0x02f9f0c0
pQh: 0xa2f9f120, pQh->qh_dma_addr: 0x02f9f120
--> short transfer
Connect USB disk /dev/sdx/, path usb:1
Port device number:7 Lun:0 Id:64
disk_connected.970

read_mbr.659

_parse_mbr_sector.353

_parse_gpt_partition.306

_parse_gpt_partition.315,gpt_sector:2

_parse_gpt_partition,gpt_nr:1,start:2048 ,end:15761470 ,size:15759422
_parse_gpt_partition.340

@@ Host ID 0
LUN 0 is init ok
Removable MSC Lun 0
MSC plug in
RASP from TSIF_RASP
RASP from TSIF_RASP
RASP from TSIF_RASP
RASP from TSIF_RASP
RASP from TSIF_RASP
[[utopia]]      ===== Check Audio Decoder Protection from hash-key IP =====
[[utopia]]      Hash Key Check DD Fail, no DD license!!
[[utopia]]      Hash Key Check DDP Fail, no DD+ license!!
[[utopia]]      Hash Key Check Dolby MS11 Fail, no Dolby MS11 license!!
[[utopia]]      Hash Key Check Dolby MS12 LC profile Fail, no Dolby MS12 LC profile license!!
[[utopia]]      Hash Key Check Dolby MS12 D profile Fail, no Dolby MS12 C profile license!!
[[utopia]]      Hash Key Check Dolby MS12 B profile Fail, no Dolby MS12 B profile license!!
[[utopia]]      Hash Key Check Dolby Pulse(MS10_DDT) Fail, no Dolby Pulse(MS10_DDT) license!!
[[utopia]]      Hash-key Support Generic HE-AAC!!
[[utopia]]      Hash Key Check DDCO Fail, no DDCO license!!
[[utopia]]      Hash Key Check DTS Fail, no DTS license!!
[[utopia]]      Hash Key Check WMA Fail, no WMA license!!
[[utopia]]      Hash Key Check DRA Fail, no DRA license!!
[[utopia]]      Hash Key Check DTSLBR Fail, no DTSLBR license!!
[[utopia]]      Hash Key Check DTSE Fail, no DTSE license!!
[[utopia]]      Hash Key Check DTSNeoUltra Fail, no DTSNeoUltra license!!
[[utopia]]      Hash Key Check SRS_TSHD Fail, no SRS_TSHD license!!
[[utopia]]      Hash Key Check SRS_THEATERSOUND Fail, no SRS_THEATERSOUND license!!
[[utopia]]      Hash Key Check DTS_StudioSound3D Fail, no DTS_StudioSound3D license!!
[[utopia]]      Hash Key Check COOK Fail, no COOK license!!
[[utopia]]      Hash Key Check DTS_HD Fail, no DTS_HD license!!
[[utopia]]      Hash Key Check Dolby volume Fail, no Dolby volume license!!
[[utopia]]      Hash Key Check SRS_PURESND Fail, no SRS_PURESND license!!
[[utopia]]      ===== Check Protection IP End                         =====
[[utopia]]
 ==========DSP Version Check==================

!!!!!!!!!!![_FirstTaskStart][1612] Driver initial time 3499
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[NMGR][appNetMgr_Init][3089] NMonitor Inited
[NMGR][appNetMgr_Init][3090] NMGR Inited
CVBS ON, RGB OFF, HDMI ON
[NMGR][appNetMgr_LoadLinkType][2687] LINK TYPE>>>  LAN
1999 drvEMAC_GetMacAddr
Mac addr 00:30:1b:ba:02:db
2293 EMAC_Control data 0x806a8184 data_length 6
2327 EMAC_Control Not support key
[msCHIP_DAC_SetOutputSource][156] input bitmap: 0x00000011
CVBS on
SVIDEO off, YPBPR off, RGB on
SCART on
[msAPI_XC_ReMapComponentType][440]: msAPI_XC eTiming = 6
[Hal_VE_EnableDI][1841] bEnable = 0, bIsDNR2VE = 0
[App_DTVManger_CreateObject][217] create DTV object success (1).
[ZUI] init: sz_msg_q=6216
Decompress_bmp_data_size = 562896
MDrv_HDMITx_EdidChecking::block 0 ==>
0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x10, 0xAC, 0x48, 0xF0, 0x4C, 0x37, 0x54, 0x41,
0x23, 0x18, 0x01, 0x03, 0x80, 0x34, 0x20, 0x78, 0xEA, 0x1D, 0xF5, 0xAE, 0x4F, 0x35, 0xB3, 0x25,
0x0D, 0x50, 0x54, 0xA5, 0x4B, 0x00, 0x81, 0x80, 0xA9, 0x40, 0xD1, 0x00, 0x71, 0x4F, 0x01, 0x01,
0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3C, 0x80, 0xA0, 0x70, 0xB0, 0x23, 0x40, 0x30, 0x20,
0x36, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1A, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x38, 0x34, 0x4B,
0x39, 0x36, 0x34, 0x38, 0x51, 0x41, 0x54, 0x37, 0x4C, 0x0A, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x44,
0x45, 0x4C, 0x4C, 0x20, 0x55, 0x32, 0x34, 0x31, 0x33, 0x0A, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD,
0x00, 0x38, 0x4C, 0x1E, 0x51, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xBD,

MDrv_HDMITx_EdidChecking::Extension Block Number = 1
MDrv_HDMITx_EdidChecking::Block #1
0x02, 0x03, 0x25, 0xF1, 0x50, 0x90, 0x05, 0x04, 0x03, 0x02, 0x07, 0x16, 0x01, 0x1F, 0x12, 0x13,
0x14, 0x20, 0x15, 0x11, 0x06, 0x23, 0x09, 0x1F, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38,
0x2D, 0x83, 0x01, 0x00, 0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45,
0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58,
0x2C, 0x25, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x9E, 0x01, 0x1D, 0x00, 0x72, 0x51, 0xD0, 0x1E,
0x20, 0x6E, 0x28, 0x55, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x8C, 0x0A, 0xD0, 0x8A, 0x20,
0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16,

_MDrv_HDMITx_ParseCEAExtEdid::Short Video Block: 16
_MDrv_HDMITx_ParseCEAExtEdid::Short Audio Block:3
_MDrv_HDMITx_ParseCEAExtEdid::VSDB
Physcal Address = [1, 0, 0, 0]
_MDrv_HDMITx_ParseHdmiVSDB::Support AI = 0 !
_MDrv_HDMITx_ParseDeepColorInfo::Support Color Depth 36-bit
ubSYNSet=253c82, dSYNCLK=928, dSSC_Span=773, dSSC_Step=3
dPixel_Clk=74
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[FE][ERR][MApi_FEM_GetFEType:420] INVALID_FEM_HANDLER
drv_frontend_index = 0 u32BroadcastType = 3
=========================== Broadcast Type List ==========================
 0x0 -> BROADCAST_TYPE_NOT_SEETING
 0x1 -> DVBC
 0x2 -> DVBT
 0x3 -> DVBT2
 0x4 -> ISDBT
 0x5 -> DVBS
 0x6 -> ATSC
 0x7 -> J83B
 0xa -> DTMB
 0xb -> DVBS2
 0xf -> DSS
 0x10 -> ATV_PAL
 0x11 -> ATV_SECAM_L_PRIME
 0x12 -> ATV_NTSC
========================== End Broadcast Type List =======================
[_SI_MutexLock][350] Err: SI mutex does not exsit!
Won't init EPG since EPGDB enable is set to false!
[MApi_SI_System_Startup] OK !!
Won't init EPG since EPGDB enable is set to false!


 DTV version: hello
 BSP version: hello
 DDI_MISC version: hello
 OTT version: hello
[ZAPPER][ERR][_appZapper_Command:5439] u8ZapHandle is wrong [255]
[GOP_GWIN_Is32FBExist][5728]FbId 255  is out of range
[MWPVR] Not Initialize PVR!
SetFileEndAutoResume => 1
[MApi_PVR_Configure][3257]: Program Change Auto mode !!
leave MApp_ZUI_API_InitCanvasGDI -> MApp_ZUI_API_GetFontMVF in 131
[MApp_ZUI_API_InitDisplayGDI][306]Lala:Hello~ SINGLE BUFFER is disable!!!!!!!
[GOP_GWIN_Is32FBExist][5728]FbId 255  is out of range
 Get timeout_ms = 0
[appVdec][apiVideo_CTRL_Exit][000660]    *******************************************************
[appVdec][apiVideo_CTRL_Exit][000661]    apiVideo_CTRL_Exit  return fail!!!
[appVdec][apiVideo_CTRL_Exit][000662]    *******************************************************
[appDmx][apiPID_CTRL_Filter_Setup][000472]    [apiPID_CTRL_Filter_Setup][472]
[appDmx][apiPID_CTRL_Filter_Open][000354]    Set Pid:2011 to Filter:63 OK !
[appDmx][apiPID_CTRL_Filter_Setup][000472]    [apiPID_CTRL_Filter_Setup][472]
[appDmx][apiPID_CTRL_Filter_Open][000354]    Set Pid:2012 to Filter:62 OK !
<Bad format string: 803F6628 : 803FB500 803FA55C 803FC5F4 B94 1 1B1B0012 800D6B74 1>
[SYS][ERR][apiVideo_CTRL_EnableTurboMode:776] [ERR] VDEC Turbo Mode fail
[appVdec][apiVideo_CTRL_Exit][000660]    *******************************************************
[appVdec][apiVideo_CTRL_Exit][000661]    apiVideo_CTRL_Exit  return fail!!!
[appVdec][apiVideo_CTRL_Exit][000662]    *******************************************************
[appVdec][apiVideo_CTRL_Init][000587]    VDEC FW add = 0xc40000
[appVdec][apiVideo_CTRL_Init][000588]    VDEC FB add = 0x1210000
[appVdec][apiVideo_CTRL_Init][000589]    VDEC BS add = 0xe10000
E_VDEC_EX_V2_USER_CMD_DYNAMIC_CMA_MODE 0x1
HAL_VPU_EX_SetDbgLevel eLevel=0x1
<Bad format string: 804D4490 : 804D4FA0 A16 0 0 807772B0 0 2000 BF200000>
HVD power on
[HAL_VPU_EX_TaskCreate][1948] create task : id 0x4040, cmd 0x40101, arg 0xc0000, bbuID 0, offset 0
[appVdec][apiVideo_CTRL_Init][000628]    *******************************************************
[appVdec][apiVideo_CTRL_Init][000629]    apiVideo_CTRL_Init  Init OK!!!
[appVdec][apiVideo_CTRL_Init][000630]    *******************************************************
[appDmx][apiPID_CTRL_Filter_Setup][000472]    [apiPID_CTRL_Filter_Setup][472]
[appDmx][apiPID_CTRL_Filter_Open][000354]    Set Pid:2011 to Filter:61 OK !
PAT version changed. old(ff), new(14)
NIT version changed. old(ff), new(1a)
[HAL_MVOP_SetDefaultClk] clock = 160000000
[HAL_MVOP_SetDefaultClk] clock = 160000000
[Warning] xc support pVOPTiming->u16H_TotalCount >= 4095 after CL 712830
NIT version changed. old(ff), new(1a)
[msAPI_XC_GetComponentType][354]: MS_COMPONENT_OUTPUT_TYPE =6
w:1920  h:1080
[1663][_XC_CalculateAFD_Window]AFD VALUE: 10
[1846][_XC_CalculateAFD_Window] Currently, AFD only support 16:9 Pillarbox or 4:3 Letterbox or Auto mode on HummingBird platform
=====EN_ASPECT_RATIO_FULL=====
[2333][tvvideo_SetAspectRatio] CropWin: (0, 0, 720, 576)
[2334][tvvideo_SetAspectRatio] DestWin: (0, 0, 1920, 1080)
====No Crop for RFBL==
MVOP is 1P mode
Please check the Scaler ID and eWindow
unknown IOCTL 10


!!!!!!!!!!![App_DTVManger_HandleSignalChange][679] bLock = 1, _eZapperTaskState = E_TASK_STATE_ZAPPER_AV_WAITSYNC, _bAVOutDone = 0
[ZAPPER][ERR][_Zapper_Pmt_SecGetInit:848] Buffer id ??
[ZAPPER][ERR][_appZapper_Command:5439] u8ZapHandle is wrong [1]
SDT version changed. old(ff), new(a)
ON_ID changed. old(0), new(2283)
TS_ID changed. old(0), new(b)
PAT version changed. old(ff), new(14)
PMT version changed. old(ff), new(1)
AddPID u16pid=0x7db u32pidfilter=0x0 enFltType=0
AddPID u16pid=0x7db u32pidfilter=0x0 enFltType=6
AddPID u16pid=0x7da u32pidfilter=0x0 enFltType=3
AddPID u16pid=0x7dc u32pidfilter=0x0 enFltType=1
AddPID u16pid=0x12 u32pidfilter=0x0 enFltType=3
duplicate PID u16pid=0x7dc enFltType=0x1
duplicate PID u16pid=0x7dc enFltType=0x1
AddPID u16pid=0x7de u32pidfilter=0x0 enFltType=4
Slice mode: u64FileSliceSize = 0x0
[../../src/espvr/core/src_v4/path/PVR_Path_Manager1.cpp][CreateDownloadPath][213]The Path_Download_Push thread 0 has been create u8recordidx:0 address:80AB8EF0
[../../src/espvr/core/src_v4/path/PVR_Path_Manager1.cpp][CreateDownloadPath][217]pathidx 0
PVR_Data_RingBuffer u32BufferReadPointer=0x2ba7760 u32BufferStart=0x2ba7760
[ZAPPER][ERR][_appZapper_Command:5439] u8ZapHandle is wrong [10]
[6708][../../../DTV/platform/zui/pageview/MApp_ZUI_ACTtvbanner.c,892(_ShowScrambMSG)] bShow[0] bFlashPopupMsg[1] MApp_ServiceInfo_IsServiceLocked[0] MApp_ServiceInfo_IsServicePasswdChecked[0] MApp_ZUI_GetActiveOSD[9]


!!!!!!!!!!![_Zapper_AV_EnVOut][5808] Video output time 7562
[MApi_PVR_BackRecordStop][2707]Stop Background handle 0
!!!!!!!!!!!!!!!! pDonwload:0x80ab8ef0 hRecord:0 Speed:1000!!!!!!!!!!!!!!!!!
!!!!!!!!!!!!!!!! pDonwload:0x80ab8ef0 END!!!!!!!!!!!!!!!!!
Download[0] closed
AddPID u16pid=0x7db u32pidfilter=0x0 enFltType=0
AddPID u16pid=0x7db u32pidfilter=0x0 enFltType=6
AddPID u16pid=0x7da u32pidfilter=0x0 enFltType=3
AddPID u16pid=0x7dc u32pidfilter=0x0 enFltType=1
AddPID u16pid=0x12 u32pidfilter=0x0 enFltType=3
duplicate PID u16pid=0x7dc enFltType=0x1
duplicate PID u16pid=0x7dc enFltType=0x1
AddPID u16pid=0x0 u32pidfilter=0x0 enFltType=4
AddPID u16pid=0x7de u32pidfilter=0x0 enFltType=4
Slice mode: u64FileSliceSize = 0x0
[../../src/espvr/core/src_v4/path/PVR_Path_Manager1.cpp][CreateDownloadPath][213]The Path_Download_Push thread 0 has been create u8recordidx:0 address:80AB8EF0
[../../src/espvr/core/src_v4/path/PVR_Path_Manager1.cpp][CreateDownloadPath][217]pathidx 0
PVR_Data_RingBuffer u32BufferReadPointer=0x2ba7ff0 u32BufferStart=0x2ba7ff0
Wejdź do Menu-->Aktualizuj przez USB

Kod: Zaznacz cały

[fatfs_fo_dirread:3284] err=2 means No such entity
Rozpocznij aktualizację sygnału V5.2.1.52

Kod: Zaznacz cały

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Dec 26 2019 - 17:32:16)  MBOT-1106.0.10.936a0fd.201806111716


DRAM:
Hello U-Boot
Stack Pointer at: 83620740
mem initial, start 0x82CEE180, len 0x402000
SPI:  Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In:    serial
Out:   serial
Err:   serial
[ERROR] do_spi_init_partition:1218: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'

>>>>>>>>>>>>>>>>>>>>Start bootlogo
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showboot.................
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x3A000 0x400
offset 0x3A000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3A028 0x342516; LzmaDec 0x80B00000 0x342516 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
============= set bootargs ===============
Hit any key to stop autoboot:  0
enable dont overwrite function
Boot Check: Reboot by WDT --------
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x35FD000
[USB] Reg 0x28: 0xD000 0x35F
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
USB device specified [0]
USB partition specified [1]
reading upgrade_7T10E_HW2.0.RC26.27.2D_DIPOL_V5.2.1.52.bin

1 bytes read
USB device specified [0]
USB partition specified [1]
reading /SbootUpgrade.bin

** Unable to read "/SbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /MbootUpgrade.bin

** Unable to read "/MbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /UrsaUpgrade.bin

** Unable to read "/UrsaUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Current state ->[0x8]
zkc  do_ustar.............
MDrv_FrontPnl_showupgrade.................
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showupgrade.................
USB device specified [0]
USB partition specified [1]
reading upgrade_7T10E_HW2.0.RC26.27.2D_DIPOL_V5.2.1.52.bin

1 bytes read
reading upgrade_7T10E_HW2.0.RC26.27.2D_DIPOL_V5.2.1.52.bin

16384 bytes read
reading upgrade_7T10E_HW2.0.RC26.27.2D_DIPOL_V5.2.1.52.bin

3397776 bytes read
storage is empty
[ERROR] get_script_next_line:845: Error: the max size of one line is 1024!!!
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

>> fatload usb 0 80000000 $(ForceUpgradePath)
reading upgrade_7T10E_HW2.0.RC26.27.2D_DIPOL_V5.2.1.52.bin

3397776 bytes read

>> spi_wrc 80004000 0 339878
offset 0x0, size 0x339878
Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
initialization done!
Erasing...
Writing...
Verifying...

>> setenv usb_complete 1

>> setenv usb_upgrade 0

>> setenv OAD_NEED_UPGRADE 0

>> setenv OAD_TRIGGER_TYPE 0

>> setenv bootcmd ' spi_rdc 0x80b00000 0x3c01c 0x2fd859; LzmaDec 0x80b00000 0x2fd859 0x80000180 0x81000000; go 0x80000224;

>> setenv upgrade_mode null

>> setenv MstarUpgrade_complete 1

>> setenv bl_jpd_read_addr 0x00000000

>> setenv bl_jpd_read_size 0x00000000

>> setenv bl_jpd_write_addr 0x00000000

>> setenv bl_jpd_write_size 0x00000000

>> setenv bl_jpd_inter_addr 0x00000000

>> setenv bl_jpd_inter_size 0x00000000

>> setenv bl_dfb_framebuffer_addr 0x00000000

>> setenv ve_buffer_addr 0x00000000

>> saveenv
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

>> reset
Reset command is skipped
[ERROR] get_script_next_line:845: Error: the max size of one line is 1024!!!
AP upgrade OK!~
All Upgrade File Had Finished !!
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
resetting ...

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Aug 09 2020 - 18:32:15)  MBOT-1106.0.10.936a0fd.201806111716


DRAM:
Hello U-Boot
Stack Pointer at: 83625740
mem initial, start 0x82CEE180, len 0x402000
SPI:  uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In:    serial
Out:   serial
Err:   serial
[ERROR] do_spi_init_partition:1218: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'

>>>>>>>>>>>>>>>>>>>>Start bootlogo
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showboot.................
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x3C000 0x400
offset 0x3C000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3C01C 0x2FD859; LzmaDec 0x80B00000 0x2FD859 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x3602000
[USB] Reg 0x28: 0x2000 0x360
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
usb find store 0 !!
reading MAC.TXT

** Unable to read "MAC.TXT" from usb 0:1 **
hdcp key err

Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x3602000
[USB] Reg 0x28: 0x2000 0x360
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
reading hdcp_key.bin

** Unable to read "hdcp_key.bin" from usb 0:1 **

 There is no_hdcpfile
this is 2 -->[WriteHdcpToFlash]
WriteHdcpToFlash  _u8WriteSult  =2
============= set bootargs ===============
Hit any key to stop autoboot:  0
enable dont overwrite function
Boot Check: Reboot by WDT --------
AC on
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
usb -

Usage:
usb
offset 0x3C01C, size 0x2FD859

LZMA Decompression...buf data channge
CRC check success !!
ok
disable interrupts
## Starting application at 0x80000224 ...
1999 drvEMAC_GetMacAddr
cyg_if_attach.225 - After initialize list 0x80619704
IFP: 0x806196f4 (eth0)
cyg_if_attach.290 - After inserting 0x8088f0d0 into list 0x80619704
IFP: 0x806196f4 (eth0)
IFA: 0x8088f0d0 - <<0x8088f14c>>
===> rt_ecos_init()
cyg_if_attach.225 - After initialize list 0x806c6144
IFP: 0x806c6134 (ra0)
cyg_if_attach.290 - After inserting 0x8088efd0 into list 0x806c6144
IFP: 0x806c6134 (ra0)
IFA: 0x8088efd0 - <<0x8088f04c>>
cyg_if_attach.225 - After initialize list 0x8093a040
IFP: 0x8093a030 (lo0)
cyg_if_attach.290 - After inserting 0x8088eed0 into list 0x8093a040
IFP: 0x8093a030 (lo0)
IFA: 0x8088eed0 - <<0x8088ef4c>>
Register_netisr [2] fun=0x800e57d5

[eCos][CPU INFO] : CPU Clock = 750000000 : RTC Period = 375000
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[eCos] UtopiaInit

shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
[SYS][ERR][AESDMARegisterToUtopia:2320] Not support AESDMA
Flash is detected (0x0D00, 0x5E, 0x40, 0x16)

0046119500d0
Auth OK
[SYS][ERR][SysInit:1761] ###############################################################
[SYS][ERR][SysInit:1762] #       System boot from WDT timeout !!!!!!!!!!!!!!!!!!!      #
[SYS][ERR][SysInit:1763] #       System boot from WDT timeout !!!!!!!!!!!!!!!!!!!      #
[SYS][ERR][SysInit:1764] #       System boot from WDT timeout !!!!!!!!!!!!!!!!!!!      #
[SYS][ERR][SysInit:1765] ###############################################################
 <FWTSP> : RASP from TSIF_RASP
Mstar USB initial, 4 ports suppor>> FwVersion:002F2600 , Date:20140924
[FUNC MApi_DB_DFT_GetPCHIntf_CT] [pstIntf  0x803ad5b4]
ted
[NCM] The allocted address is 0xa2f7dfe0
Init Software Timer ok
usbcore: regtered new driver hub
[USB] quirk list init, support max 20
usbcore: regtered new driver usb-storage
[USB] MS USB Host Lib for K5AP only


rtusb init rt2870 --->


usbcore: regtered new driver rt2870
Init chip K5AP, port 0
[USB] constant upll NLib, UTMI base 0xbf207500, USBC base 0xbf200e00, UHC base 0xbf204800, USBBC base 0xbf226e00
[USB] init squelch level 0x2
ehci_hcd (CPE_AMBA) at 0x0xbf204800, irq 7
new USB Bus, assigned pBus number 1
pQh: 0xa2f7e000, pQh->qh_dma_addr: 0x02f7e000
periodic frame list array 0xa2f80000, size 1024
[EHCI] Enable Park Mode: 3
EHCI 1.00, driver eCos Newhost
[root hub] device address 1
[MApp_CheckFlash][1850] s8SN0 = 1 dex 3) = MStar eCos 1.0 ehci_hcd
[App_DTVManger_SetParentCtlPwdStatus][590] DTV Object not created yet
[App_DTVManger_SetParentCtlStatus][557] DTV Object not created yet

USB device product string (index 2) = CPE_AMBA EHCI
USB device serial number string (index 1) = cpe_ehci
usbdev 1-0 - registering interface 1-0:0
USB hub found
1 port detected

Usb start EX..., pRootHub = 806597d8

[[utopia]]      Start HAL_AUDIO_AllocateVars InitShmFlaUTask EX>> .g=0
App_InitBlockData!
[time:1403][MApi_DB_CM_InitDTVDataManager:1660] start!!
[time:1408][MApi_DB_CM_PrintAllProgram:6657]    === DTV Programs ===
[time:1414][MApi_DB_CM_PrintAllProgram:6664]    === RADIO Programs ===
[time:1419][MApi_DB_CM_PrintAllProgram:6671]

[time:1424][MApi_DB_CM_PrintAllProgram:6657]    === DTV Programs ===
[time:1429][MApi_DB_CM_PrintAllProgram:6664]    === RADIO Programs ===
[time:1435][MApi_DB_CM_PrintAllProgram:6671]

[CreatDTVProgramIndexTableAndProgramIDTable,6976] DTV Data Structure is valid

[time:1446][FillDTVProgramIndexTableWithOrder:7134]       start!!
.. port 0 starting
UTask EX>> USB Port 0create Audio SHM data ...
Audio SHM data is created
reset is connected
 Audio SHM data ...
[[utopia]][audio]      MStar AUDIO Driver Version : 2.2.3
[[utopia]]      Start HAL_AUDIO_AllocateVars InitShmFlag=1
[[utopia]]      HAL_AUDIO_AllocateVars QUERY ClientCounter=1
[[utopia]]      MDrv_AUDIO_PCM_Init: Init PCM device
[time:2557][check_uid_entryption:1546]  start!!
[time:2561][check_uid_entryption:1551]  u8UIDLength =8
[time:2565][check_uid_entryption:1552]  uid_data:
 D5 00 B6 92 12 67 1C 58
[time:2572][check_uid_entryption:1566]  MDrv_FLASH_OTP_Read 0x2000(32) Success!!
 34 29 9E 2F 16 59 0D 56 1B DB 64 73 05 C0 3E 74 D5 77 5D B0 F0 E7 14 6F C6 82 01 FD C9 D9 18 24
[time:2587][check_uid_entryption:1580]  flash_digest:
 34 29 9E 2F 16 59 0D 56 1B DB 64 73 05 C0 3E 74 D5 77 5D B0 F0 E7 14 6F C6 82 01 FD C9 D9 18 24
[time:2600][check_uid_entryption:1583]  sha_digest:
 53 64 A7 D4 FE B9 25 6F 21 D8 4C 4B 2A 54 4D 0B 9A 80 C1 DF 8D 43 32 F8 9E B4 6E D1 CB 8F 28 96
[time:2613][check_uid_entryption:1590]  Check uid entryption failed!
MApi_VectorFont_Init total size=1310720, free size=679648, large size=679636
[xxxx]=====func:MVF_New_Face==line:160======TASKRUN======
[xxxx]=====func:MVF_New_Face==line:243======TASKRUN======

 0
...[MApp_ZUI_API_GetLanguageNum, 107] u8LanguageNum = 9...
stSysSetting.LedDimmer =8
<saved irq> portsc[0x 803], usbcmd[10b09]
hub_port_connect_change ===20180329===> port 1, status 1, change 1
[SYS][ERR][_SysInit_GetColorFMTCMD:1071] fail to get color format failed!!
MDrv_PNL_Init u32PnlRiuBaseAddr = bf200000
MDrv_PNL_Init u32PMRiuBaseAddr = bf000000
[XC,Version] 00709801
 no need to patch
RootHub SPEED: high-speed
:: Device Speed is 480 Mb/s
new USB device on path usb:1, assigned address 2
pQh: 0xa2f7e060, pQh->qh_dma_addr: 0x02f7e060
MDrv_HDMITx_EdidChecking::block 0 ==>
0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x10, 0xAC, 0x48, 0xF0, 0x4C, 0x37, 0x54, 0x41,
0x23, 0x18, 0x01, 0x03, 0x80, 0x34, 0x20, 0x78, 0xEA, 0x1D, 0xF5, 0xAE, 0x4F, 0x35, 0xB3, 0x25,
0x0D, 0x50, 0x54, 0xA5, 0x4B, 0x00, 0x81, 0x80, 0xA9, 0x40, 0xD1, 0x00, 0x71, 0x4F, 0x01, 0x01,
0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3C, 0x80, 0xA0, 0x70, 0xB0, 0x23, 0x40, 0x30, 0x20,
0x36, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1A, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x38, 0x34, 0x4B,
0x39, 0x36, 0x34, 0x38, 0x51, 0x41, 0x54, 0x37, 0x4C, 0x0A, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x44,
0x45, 0x4C, 0x4C, 0x20, 0x55, 0x32, 0x34, 0x31, 0x33, 0x0A, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD,
0x00, 0x38, 0x4C, 0x1E, 0x51, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xBD,

MDrv_HDMITx_EdidChecking::Extension Block Number = 1
MDrv_HDMITx_EdidChecking::Block #1
0x02, 0x03, 0x25, 0xF1, 0x50, 0x90, 0x05, 0x04, 0x03, 0x02, 0x07, 0x16, 0x01, 0x1F, 0x12, 0x13,
0x14, 0x20, 0x15, 0x11, 0x06, 0x23, 0x09, 0x1F, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38,
0x2D, 0x83, 0x01, 0x00, 0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45,
0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58,
0x2C, 0x25, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x9E, 0x01, 0x1D, 0x00, 0x72, 0x51, 0xD0, 0x1E,
0x20, 0x6E, 0x28, 0x55, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x8C, 0x0A, 0xD0, 0x8A, 0x20,
0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16,

_MDrv_HDMITx_ParseCEAExtEdid::Short Video Block: 16
_MDrv_HDMITx_ParseCEAExtEdid::Short Audio Block:3
_MDrv_HDMITx_ParseCEAExtEdid::VSDB
Physcal Address = [1, 0, 0, 0]
_MDrv_HDMITx_ParseHdmiVSDB::Support AI = 0 !
_MDrv_HDMITx_ParseDeepColorInfo::Support Color Depth 36-bit
DAC eTiming =6
DAC Panel Table Index =6
[time:3704][appCEC_Init:347]    start!
[SYS][ERR][_SysInit_GetPanelCMD:1050] fail to get panel failed!!
Wait V Sync!!
usb new device VID = 23a9, PID = ef18
USB device manufacturer string (index 1) = USB
USB device product string (index 2) = DISK
usbdev 1-1 - registering interface 1-1:0
find USB MSC device at device number 2
<saved irq> portsc[0x   d], usbcmd[10b09]
pQh: 0xa2f7e0c0, pQh->qh_dma_addr: 0x02f7e0c0
pQh: 0xa2f7e120, pQh->qh_dma_addr: 0x02f7e120
--> short transfer
Connect USB disk /dev/sdx/, path usb:1
Port device number:7 Lun:0 Id:64
disk_connected.970

read_mbr.659

_parse_mbr_sector.353

_parse_gpt_partition.306

_parse_gpt_partition.315,gpt_sector:2

_parse_gpt_partition,gpt_nr:1,start:2048 ,end:15761470 ,size:15759422
_parse_gpt_partition.340

@@ Host ID 0
LUN 0 is init ok
Removable MSC Lun 0
MSC plug in
[Hal_VE_EnableDI][1841] bEnable = 0, bIsDNR2VE = 0
[[utopia]]      ===== Check Audio Decoder Protection from hash-key IP =====
[[utopia]]      Hash Key Check DD Fail, no DD license!!
[[utopia]]      Hash Key Check DDP Fail, no DD+ license!!
[[utopia]]      Hash Key Check Dolby MS11 Fail, no Dolby MS11 license!!
[[utopia]]      Hash Key Check Dolby MS12 LC profile Fail, no Dolby MS12 LC profile license!!
[[utopia]]      Hash Key Check Dolby MS12 D profile Fail, no Dolby MS12 C profile license!!
[[utopia]]      Hash Key Check Dolby MS12 B profile Fail, no Dolby MS12 B profile license!!
[[utopia]]      Hash Key Check Dolby Pulse(MS10_DDT) Fail, no Dolby Pulse(MS10_DDT) license!!
[[utopia]]      Hash-key Support Generic HE-AAC!!
[[utopia]]      Hash Key Check DDCO Fail, no DDCO license!!
[[utopia]]      Hash Key Check DTS Fail, no DTS license!!
[[utopia]]      Hash Key Check WMA Fail, no WMA license!!
[[utopia]]      Hash Key Check DRA Fail, no DRA license!!
[[utopia]]      Hash Key Check DTSLBR Fail, no DTSLBR license!!
[[utopia]]      Hash Key Check DTSE Fail, no DTSE license!!
[[utopia]]      Hash Key Check DTSNeoUltra Fail, no DTSNeoUltra license!!
[[utopia]]      Hash Key Check SRS_TSHD Fail, no SRS_TSHD license!!
[[utopia]]      Hash Key Check SRS_THEATERSOUND Fail, no SRS_THEATERSOUND license!!
[[utopia]]      Hash Key Check DTS_StudioSound3D Fail, no DTS_StudioSound3D license!!
[[utopia]]      Hash Key Check COOK Fail, no COOK license!!
[[utopia]]      Hash Key Check DTS_HD Fail, no DTS_HD license!!
[[utopia]]      Hash Key Check Dolby volume Fail, no Dolby volume license!!
[[utopia]]      Hash Key Check SRS_PURESND Fail, no SRS_PURESND license!!
[[utopia]]      ===== Check Protection IP End                         =====
[[utopia]]
 ==========DSP Version Check==================

!!!!!!!!!!![_FirstTaskStart][1616] Driver initial time 5504
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[time:5515][_appMain_Task:2213] ENTER_STANDBY = 0
[NMGR][appNetMgr_Init][3092] NMonitor Inited
[NMGR][appNetMgr_Init][3093] NMGR Inited
CVBS ON, RGB OFF, HDMI ON
[NMGR][appNetMgr_LoadLinkType][2700] LINK TYPE>>> WLAN
iwpriv ra0 set RadioOn=1
[NMGR][_CheckNetworkStatus_WLAN][1543] NET_STATE_DEVICE_NOTREADY
[msCHIP_DAC_SetOutputSource][156] input bitmap: 0x00000011
CVBS on
SVIDEO off, YPBPR off, RGB on
SCART on
[time:5600][_SetHDMI:394]       audioType =7  eHDMIType=1
[time:5666][_SetDeviceMute:508] bMute = 0
[msAPI_XC_ReMapComponentType][440]: msAPI_XC eTiming = 6
[Hal_VE_EnableDI][1841] bEnable = 0, bIsDNR2VE = 0
[App_DTVManger_CreateObject][217] create DTV object success (1).
[ZUI] init: sz_msg_q=6216
Decompress_bmp_data_size = 547360
MDrv_HDMITx_EdidChecking::block 0 ==>
0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x10, 0xAC, 0x48, 0xF0, 0x4C, 0x37, 0x54, 0x41,
0x23, 0x18, 0x01, 0x03, 0x80, 0x34, 0x20, 0x78, 0xEA, 0x1D, 0xF5, 0xAE, 0x4F, 0x35, 0xB3, 0x25,
0x0D, 0x50, 0x54, 0xA5, 0x4B, 0x00, 0x81, 0x80, 0xA9, 0x40, 0xD1, 0x00, 0x71, 0x4F, 0x01, 0x01,
0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3C, 0x80, 0xA0, 0x70, 0xB0, 0x23, 0x40, 0x30, 0x20,
0x36, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1A, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x38, 0x34, 0x4B,
0x39, 0x36, 0x34, 0x38, 0x51, 0x41, 0x54, 0x37, 0x4C, 0x0A, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x44,
0x45, 0x4C, 0x4C, 0x20, 0x55, 0x32, 0x34, 0x31, 0x33, 0x0A, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD,
0x00, 0x38, 0x4C, 0x1E, 0x51, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xBD,

MDrv_HDMITx_EdidChecking::Extension Block Number = 1
MDrv_HDMITx_EdidChecking::Block #1
0x02, 0x03, 0x25, 0xF1, 0x50, 0x90, 0x05, 0x04, 0x03, 0x02, 0x07, 0x16, 0x01, 0x1F, 0x12, 0x13,
0x14, 0x20, 0x15, 0x11, 0x06, 0x23, 0x09, 0x1F, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38,
0x2D, 0x83, 0x01, 0x00, 0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45,
0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58,
0x2C, 0x25, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x9E, 0x01, 0x1D, 0x00, 0x72, 0x51, 0xD0, 0x1E,
0x20, 0x6E, 0x28, 0x55, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x8C, 0x0A, 0xD0, 0x8A, 0x20,
0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16,

_MDrv_HDMITx_ParseCEAExtEdid::Short Video Block: 16
_MDrv_HDMITx_ParseCEAExtEdid::Short Audio Block:3
_MDrv_HDMITx_ParseCEAExtEdid::VSDB
Physcal Address = [1, 0, 0, 0]
_MDrv_HDMITx_ParseHdmiVSDB::Support AI = 0 !
_MDrv_HDMITx_ParseDeepColorInfo::Support Color Depth 36-bit
ubSYNSet=253c82, dSYNCLK=928, dSSC_Span=773, dSSC_Step=3
dPixel_Clk=74
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[FE][ERR][MApi_FEM_GetAvailableFEResource:449] Obtain s32_FEM_ResourceMutex failed.
[FE][ERR][MApi_FEM_GetFEType:419] INVALID_FEM_HANDLER
[FE][ERR][_FEM_GetFEConfigByHandler:1237] Invalid handler !
[FE][ERR][MApi_FEM_Tune2RfCh:634] Wrong Handler
[time:6590][appMain_GetWakeupType:1660] MDrv_PM_GetWakeupSource = 0
[time:6596][_GetWakeupType:1533]        Start!
[time:6599][_GetWakeupType:1599]        return 0
[time:6590][MApi_DateTime_Init:485]     appMain_GetWakeupType()=0
[time:6608][appMain_GetWakeupType:1660] MDrv_PM_GetWakeupSource = 0
[time:6614][_GetWakeupType:1533]        Start!
[time:6618][_GetWakeupType:1599]        return 0
[_SI_MutexLock][350] Err: SI mutex does not exsit!
MApi_EpgDB_SetExtendedEventPoolSize 0x4e0000
[EPGDB][000812]  =========================================================================
[EPGDB][000813]  _pu8EitBufMask:        (Start, End, Length)= (0xa2ef8580, 0xa2ef8585, 0x00000005)
[EPGDB][000814]  _pMapBufIdxTable:      (Start, End, Length)= (0xa2eae660, 0xa2eae7f0, 0x00000190)
[EPGDB][000815]  _pu8EpgDbEvtMask       (Start, End, Length)= (0xa2ef8300, 0xa2ef8571, 0x00000271)
[EPGDB][000816]  _pu8EpgDbScheHdrList   (Start, End, Length)= (0xa2ef77b0, 0xa2ef82f0, 0x00000b40)
[EPGDB][000817]  _pu8EpgDbSrvEvtList    (Start, End, Length)= (0xa2eeda20, 0xa2ef77a0, 0x00009d80)
[EPGDB][000818]  _pu8EpgDbSrvSecList    (Start, End, Length)= (0xa2ed9a10, 0xa2eeda10, 0x00014000)
[EPGDB][000819]  _pu8EpgDbEvtHdrList    (Start, End, Length)= (0xa2eb2900, 0xa2ed9a00, 0x00027100)
[EPGDB][000820]  _pu8EpgDbPfHdrList     (Start, End, Length)= (0xa2eb2820, 0xa2eb28e8, 0x000000c8)
[EPGDB][000821]  _pu8EpgDbPfPresent     (Start, End, Length)= (0xa2eb0810, 0xa2eb2810, 0x00002000)
[EPGDB][000822]  _pu8EpgDbPfFollow      (Start, End, Length)= (0xa2eae800, 0xa2eb0800, 0x00002000)
[EPGDB][000827]  EPG database allocate 0x00529e8e bytes
[EPGDB][000833]  =========================================================================
MApi_EpgDB_Clear : Reset eit buffer
[-]MApi_EpgDB_Init


 DTV version: hello
 BSP version: hello
 DDI_MISC version: hello
 OTT version: hello
[ZAPPER][ERR][_appZapper_Command:5439] u8ZapHandle is wrong [255]
[time:6765][MApp_ZUI_InitBootOsd:4232]  stSysSetting.fHotelMode=0
[GOP_GWIN_Is32FBExist][5728]FbId 255  is out of range
[MWPVR] Not Initialize PVR!
SetFileEndAutoResume => 1
[MApi_PVR_Configure][3202]: Program Change Auto mode !!
leave MApp_ZUI_API_InitCanvasGDI -> MApp_ZUI_API_GetFontMVF in 131
[GOP_GWIN_Is32FBExist][5728]FbId 255  is out of range
 Get timeout_ms = 0
[time:6989][_DisappearAllPopupMsg:589]  start!
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[ZAPPER][ERR][_Zapper_Signal:4656] Tuner not init yet
[FE][ERR][MApi_FEM_GetAvailableFEResource:449] Obtain s32_FEM_ResourceMutex failed.
[FE][ERR][MApi_FEM_GetFEType:419] INVALID_FEM_HANDLER
[FE][ERR][_FEM_GetFEConfigByHandler:1237] Invalid handler !
[FE][ERR][MApi_FEM_SetDTVFE:854] Wrong Handler
[FE][ERR][MApi_FEM_GetFEType:419] INVALID_FEM_HANDLER
[FE][ERR][_FEM_GetFEConfigByHandler:1237] Invalid handler !
[FE][ERR][MApi_FEM_Tune2RfCh:634] Wrong Handler
[NMGR][_CheckNetworkStatus_WLAN][1543] NET_STATE_DEVICE_NOTREADY
[NMGR][_CheckNetworkStatus_WLAN][1543] NET_STATE_DEVICE_NOTREADY
[NMGR][_CheckNetworkStatus_WLAN][1543] NET_STATE_DEVICE_NOTREADY
Naciskam Menu na pilocie

Kod: Zaznacz cały

[time:154741][MApp_ZUI_ACT_HandleTVBannerKey:5142]      key = 15 appPvr_IsPlay()=0
[time:154747][MApp_ZUI_ACT_HandleTVBannerKey:5253]      2222  key = 15
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 124
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 129
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 147
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 152
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 157
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 162
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 167

-----Show Task Stack Information-----
 ID                     Name   Total_Size     Used_Max
---END Show Task Stack Information---

Func First RA: 800C6C04
This thread stack base = 80730e8c size = 00020000, Memory Dump:

 800c6c04  00000001  00000001  808b8a8c  80620000  80750aa0  800104ec  19190012
 19190013  19190014  19190015  19190016  19190017  80750e30  800bcbe8  00000000
 fffffffe  000000ad  00940000  0000001f  00000064  00000000  808d7024  01010101
 10101010  f0fbc290  f0fbc290  00000000  00000000  00000000  00000000  80750d30
 808d5658  19190012  19190013  19190014  19190015  19190016  19190017  0000ffff
 808dd6b4  80750bb0  8014a503  806ec790  80750d00  80750e30  801eff7f  00000500
 000002aa  5e4cff8a  71ffe38f  fd765ffa  c903ffb9  be7fdee4  b7ef448c  b7fa756e
 bfd8cefd  98de7fda  73fa09d0  7fdb9fc7  c1a7e3fd  fee83361  eed50f2d  7fca51f7
 beced592  7d702b9f  f1fd4277  db7ef1a1  c764e8a8  1919ff14  1919ff15  1919ff16
 1919ff17  1919ff18  1919ff19  1919ff1a  1919ff1b  1919ff1c  1919ff1d  1919ff1e
 bfd70f71  01600000  00000010  30008c03  0000001c  801efde9  1000001c  bb27f837
 00000000  00019556  00000000  00000003  000001d2  80750cb8  80750d38  80750c34
 00000001  00000000  02d00500  00000000  02d003c0  00000000  8008501d  00000000
 00000001  805e4430  80750d38  80750c1e  00000000  80670ea8  801ef82f  805e434c
 805e41cc  000000be  000002f8  00000000  00000000  80670e98  80750c90  808d5658
 80083503  00000000  00810000  00000000  00000004  00020500  801efdf1  0000323a
 801f041f  00000000  805e4344  32393101  000000c8  808d702e  801eff7f  01db0101
 000000c9  808d702e  801ef859  807500c8  0000001e  80750cb8  000000c8  000000c8
 8008514b  00000000  00000000  382e3800  342e342e  0000ff00  00000000  00000008
 02d00500  00000000  ffffffff  ffffffff  000000ff  00000000  00000000  00000000
 00000000  00000000  00000000  00000000  00000000  00000000  00000000  00000000
 00000200  05000000  050002d0  0a0002d0  808d6fe4  00025e42  801eff7f  00000000
 00000000  02d00500  80750d38  808d0000  00000064  00000000  00280226  00000000
 801f01d7  19190014  808d7028  80750ea8  801f09bd  00000001  808d7024  00000000
 806e4cf0  80750ea8  801f0a95  00000000  00000000  808b1cf0  0000013c  808b1bac
 00000000  00000000  80750e96  80750e96  8002a937  76540001  80750dc8  00000018
 80750de4  00000002  1919ff09  1919ff0a  1919ff0b  1919ff0c  1919ff0d  80620000
 19190011  0000005b  7fffff02  803c42e7  800c9ec8  80750bcc  00000000  00000001
 00000018  1919ff18  00000000  1919ff1a  808bb2d8  19190011  801c7bcd  1919ff1e
 1919ff1f  01000000  deadbeef  808bb2e0  800cacf4  800cacc8  deadbeef  deadbeef
 deadbeef  19190010  800cacc8  deadbeef  deadbeef  deadbeef  deadbeef  deadbeef
 deadbeef  deadbeef  deadbeef  deadbeef  deadbeef  deadbeef  deadbeef  deadbeef
 deadbeef  deadbeef  808bb2e0  909ba2f0  a0ab92c0  b0bb82d0  c0cbf2a0  d0dbe2b0
 e0ebd280  f0fbc290
1: ra = 800c6c04
2: ra = 800104ec
3: ra = 801efde9
4: ra = 801eff7f
5: ra = 801f01d7
6: ra = 801f0a95
7: ra = 8002a937
8: ra = 801c7bcd
9: ra = 800cacf4
10: ra = 800cacc8
Dekoder utknął
Po kilku sekundach urządzenie uruchomi się ponownie

MaxEvans
Posty: 1185
Rejestracja: 13 listopada 2016, o 09:49
Miejscowość: Tuszyn
Odbiornik: LG Flatron M237WDP-PZ ARIVA T75 SKYMASTER STB265 WIWA LITE
Instalacja antenowa: Antena DIPOL 11 Symetryzator Kabel Televes T-100 Plus 5 m
Nadajnik - obiekt nadawczy: SLR Dąbrowa (22 km) RTCN Zygry (43 km)

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: MaxEvans »

Sprawdziłem inne oprogramowania z pierwszego postu bez zmian. Od Lite 2 działa.

@gocom a czy oprogramowanie od Vmade K6 zadziała w starej Wiwie Lite.

gocom
Posty: 94
Rejestracja: 6 lutego 2022, o 17:24
Miejscowość: RU
Odbiornik: WIWA H265 MAXX, Vmade K5, Vmade K6 AV.

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: gocom »

MaxEvans
Tak, to będzie.

Vmade K6 + SW Ariva T30
Naciskam przycisk Menu

Kod: Zaznacz cały

[time:48013][MApp_ZUI_ACT_HandleTVBannerKey:5230]       key = 15 appPvr_IsPlay()=0
[time:48019][MApp_ZUI_ACT_HandleTVBannerKey:5323]       _IsMsgKeyHandleEnable() = 0
[time:48026][MApp_ZUI_ACT_HandleTVBannerKey:5340]       2222  key = 15
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 84
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 145
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 150
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 155
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 160
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 165
 %ff
AD Absolute Value 0
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 278
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 325
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 330
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 335
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 446
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 451
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 456
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 461
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 466
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 472
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 478
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 84
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 145
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 150
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 155
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 160
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 165
 %ff
AD Absolute Value 0
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 278
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 325
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 330
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 335
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 446
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 451
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 456
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 461
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 466
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 472
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 478
Dekoder utknął

Vmade K6 + SW XORO_HRT7622_HRT7624_PVR
Po wejściu do Menu zawiesza się:

Kod: Zaznacz cały

[time:101364][MApp_ZUI_ACT_HandleTVBannerKey:5211]      key = 15 appPvr_IsPlay()=0
[time:101370][MApp_ZUI_ACT_HandleTVBannerKey:5304]      _IsMsgKeyHandleEnable() = 0
[time:101377][MApp_ZUI_ACT_HandleTVBannerKey:5321]      2222  key = 15
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 89
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 137
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 145
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 150
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 155
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 160
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 165
 %ff
AD Absolute Value 0
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 278
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 325
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 330
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 335
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 446
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 451
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 456
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 461
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 466
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 472
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 478
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 89
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 137
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 145
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 150
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 155
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 160
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 165
 %ff
AD Absolute Value 0
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 278
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 325
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 330
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 335
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 446
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 451
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 456
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 461
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 466
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 472
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 478

MaxEvans
Posty: 1185
Rejestracja: 13 listopada 2016, o 09:49
Miejscowość: Tuszyn
Odbiornik: LG Flatron M237WDP-PZ ARIVA T75 SKYMASTER STB265 WIWA LITE
Instalacja antenowa: Antena DIPOL 11 Symetryzator Kabel Televes T-100 Plus 5 m
Nadajnik - obiekt nadawczy: SLR Dąbrowa (22 km) RTCN Zygry (43 km)

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: MaxEvans »

Robię test. Dam znac.

Zygzuś
Posty: 134
Rejestracja: 22 maja 2022, o 13:25
Miejscowość: Tarnów
Odbiornik: Wiwa Maxx
Nadajnik - obiekt nadawczy: RTON G.Św.Marcina

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: Zygzuś »

Dziś kilka spostrzeżeń z używania softu Signala na maxx NEW.
Z racji wejścia w miejsce tvp3 Wa-wa Nauki chciałem bez skanowania zmienić nazwę w edycji programów i tu zonk. Nie ma w opisie tej czynności przycisku epg, tylko strzałka w kształcie banana i za chiny nie mogłem wejść w menu edycji z klawiatury. Pozostało skanowania i ostrzegam, w wiwie wystarczyło po onid dać ręczne skanowanie i dodawało na końcu kanał nowy. W signalu rozwala listy, gubi ustawienia i wg lcn jest najbliższe tego z oryginalnego ustawienia z wiwy.
W końcu udało się odpalić pełną obsługę cec, oprócz tego power on z pilota tv. W tv trzeba było grzebać w ustawieniach av bravia sync, działają numeryczne, podwójne vol, channel, kółko, menu, info, kolorowe. Jedynie brak epg, ttx, sub, które można połowicznie załatwić z menu.
Jeszcze jedna sugestia, czy można przycisk czerwony wył/wł tunera (power dvbt) zamienić w sofcie na ten programowalny z lewej (power), wówczas może zadziałać to nieszczęsne power on z pilota tv.

ukaszu
Posty: 73
Rejestracja: 15 września 2022, o 10:55
Miejscowość: Zalesie

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: ukaszu »

Dzięki @gocom za sprawdzenie!
gocom pisze: 3 października 2022, o 10:08

Kod: Zaznacz cały

Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 124
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 129
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 147
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 152
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 157
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 162
Check MApp_ZUI_ACT_GetMainMenuDynamicText  hwnd = 167
To chyba nie powinno się pokazać - nie mam kodu źródłowego, ale HWND chyba są jako const i nie powinno być tak że któregoś brakuje. Ciekawe z czego to wynika. Czy mógłbyś wgrać u siebie jakiś starszy FW od Wiwy (taki w którym menu działa) i potem nowszy też od Wiwy (gdzie Menu się zacina) i dla obu zebrać całą konsolę UART? Tam gdzieś powinna być różnica.

Dzięki @Zygzuś za testy!
Zygzuś pisze: 3 października 2022, o 13:18 Jeszcze jedna sugestia, czy można przycisk czerwony wył/wł tunera (power dvbt) zamienić w sofcie na ten programowalny z lewej (power), wówczas może zadziałać to nieszczęsne power on z pilota tv.
Odnośnie tego fragmentu to zmienić kod mogę (zwykły power to 0x41, a ten z sekcji Memo to 0xF2 o ile nie został nadpisany), ale nie rozumiem czemu wtedy zadziała power z pilota tv?

Zygzuś
Posty: 134
Rejestracja: 22 maja 2022, o 13:25
Miejscowość: Tarnów
Odbiornik: Wiwa Maxx
Nadajnik - obiekt nadawczy: RTON G.Św.Marcina

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: Zygzuś »

ukaszu pisze: 3 października 2022, o 16:07 Odnośnie tego fragmentu to zmienić kod mogę (zwykły power to 0x41, a ten z sekcji Memo to 0xF2 o ile nie został nadpisany), ale nie rozumiem czemu wtedy zadziała power z pilota tv?
Z memo odpala się tv, dzięki zapisaniu kodu z pilota tv, mógłby odpalać też tuner, gdyby nadpisywał ten kod. Pilot tv czasem jest niezbędny, np w odpalaniu usług z lan, vlan, ustawieniach obrazu, dźwięku.

ukaszu
Posty: 73
Rejestracja: 15 września 2022, o 10:55
Miejscowość: Zalesie

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: ukaszu »

Zygzuś pisze: 3 października 2022, o 16:51 Z memo odpala się tv, dzięki zapisaniu kodu z pilota tv, mógłby odpalać też tuner, gdyby nadpisywał ten kod. Pilot tv czasem jest niezbędny, np w odpalaniu usług z lan, vlan, ustawieniach obrazu, dźwięku.
OK, już rozumiem. Firmware ma filtr na DeviceId, a pilot od TV na pewno ma inny DeviceId niż Signal/Wiwa, więc STB na niego nie zareaguje bez konkretnych przeróbek.

gocom
Posty: 94
Rejestracja: 6 lutego 2022, o 17:24
Miejscowość: RU
Odbiornik: WIWA H265 MAXX, Vmade K5, Vmade K6 AV.

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: gocom »

MaxEvans
Nie spiesz się z eksperymentami. Chodziło mi o firmware Vmade z przystosowanym do niego pilotem Wiwa. Bez adaptacji nie będziesz w stanie sterować dekoderem.
ukaszu pisze: 3 października 2022, o 16:07 To chyba nie powinno się pokazać - nie mam kodu źródłowego, ale HWND chyba są jako const i nie powinno być tak że któregoś brakuje. Ciekawe z czego to wynika. Czy mógłbyś wgrać u siebie jakiś starszy FW od Wiwy (taki w którym menu działa) i potem nowszy też od Wiwy (gdzie Menu się zacina) i dla obu zebrać całą konsolę UART? Tam gdzieś powinna być różnica.
Oprogramowanie firmy Wiwa NEW nie powoduje zawieszania się przy wchodzeniu do Menu. Wyszukiwanie kanałów jest zablokowane. Postaram się zrobić jutro dziennik.

MaxEvans
Posty: 1185
Rejestracja: 13 listopada 2016, o 09:49
Miejscowość: Tuszyn
Odbiornik: LG Flatron M237WDP-PZ ARIVA T75 SKYMASTER STB265 WIWA LITE
Instalacja antenowa: Antena DIPOL 11 Symetryzator Kabel Televes T-100 Plus 5 m
Nadajnik - obiekt nadawczy: SLR Dąbrowa (22 km) RTCN Zygry (43 km)

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: MaxEvans »

Ok postaram się pilotem uniwersalnym cos zdziałać.

Zygzuś
Posty: 134
Rejestracja: 22 maja 2022, o 13:25
Miejscowość: Tarnów
Odbiornik: Wiwa Maxx
Nadajnik - obiekt nadawczy: RTON G.Św.Marcina

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: Zygzuś »

ukaszu pisze: 3 października 2022, o 17:13
Zygzuś pisze: 3 października 2022, o 16:51 Z memo odpala się tv, dzięki zapisaniu kodu z pilota tv, mógłby odpalać też tuner, gdyby nadpisywał ten kod. Pilot tv czasem jest niezbędny, np w odpalaniu usług z lan, vlan, ustawieniach obrazu, dźwięku.
OK, już rozumiem. Firmware ma filtr na DeviceId, a pilot od TV na pewno ma inny DeviceId niż Signal/Wiwa, więc STB na niego nie zareaguje bez konkretnych przeróbek.
Tak czułem, że to wymaga zaawnsowanej wersji przeróbek, więc nie ma sensu się zagłębiać.
Wgrywanie listy kanałów z wiwy wciskając 2 niby wywala błąd, ale wstaje ta lista.
Co do pilota, to brakuje obsługi 1 przycisku z signala(przycisk krzywej strzałki) i 1 na wiwie (usb) plus zamiana funkcji kolorowych z tymi od odtwarzania plików.

ukaszu
Posty: 73
Rejestracja: 15 września 2022, o 10:55
Miejscowość: Zalesie

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: ukaszu »

Zygzuś pisze: 4 października 2022, o 11:56Co do pilota, to brakuje obsługi 1 przycisku z signala(przycisk krzywej strzałki) i 1 na wiwie (usb) plus zamiana funkcji kolorowych z tymi od odtwarzania plików.
Czy krzywa strzałka to back/wstecz? Na pilocie od Wiwy chyba go nie ma, przynajmniej na MC-006.

Zygzuś
Posty: 134
Rejestracja: 22 maja 2022, o 13:25
Miejscowość: Tarnów
Odbiornik: Wiwa Maxx
Nadajnik - obiekt nadawczy: RTON G.Św.Marcina

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: Zygzuś »

ukaszu pisze: 4 października 2022, o 12:14
Zygzuś pisze: 4 października 2022, o 11:56Co do pilota, to brakuje obsługi 1 przycisku z signala(przycisk krzywej strzałki) i 1 na wiwie (usb) plus zamiana funkcji kolorowych z tymi od odtwarzania plików.
Czy krzywa strzałka to back/wstecz? Na pilocie od Wiwy chyba go nie ma, przynajmniej na MC-006.
Tak, na pilotach wiwy nie ma, a obsługuje np. Folder w górę czy zmianę nazwy kanału. Na pilocie wiwy robił to inny przycisk, bodajże epg.
Ostatnio zmieniony 5 października 2022, o 13:45 przez Zygzuś, łącznie zmieniany 1 raz.

gocom
Posty: 94
Rejestracja: 6 lutego 2022, o 17:24
Miejscowość: RU
Odbiornik: WIWA H265 MAXX, Vmade K5, Vmade K6 AV.

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: gocom »

@ukaszu
Vmade K6 + SW Wiwa Pro(eth) 5.1.0.52

Po naciśnięciu przycisku Menu w konsoli nie są wyświetlane żadne informacje.
Wyszukiwanie kanałów rozpoczęte:

Kod: Zaznacz cały

Current Braodcast Type [0]
[MApp_ZUI_ACT_TerminateMainMenu][8225]
[MApp_SaveGenSetting][1910]
Set Scan table, FE type[0]
[FE][ERR][MApi_FEM_GetFEhandler:888] There is no FE in status [1]
Max Channel = 70
Min Channel = 5
 === [MApp_MenuChannel_FullScan_Start]==== Start FQ = 177500 , End FQ = 866000

 ================== scanParam.bScanMode[1]
_ChScan_Tune2RF: 177500KHz
drv_frontend_index = 0 u32BroadcastType = 2
=========================== Broadcast Type List ==========================
 0x0 -> BROADCAST_TYPE_NOT_SEETING
 0x1 -> DVBC
 0x2 -> DVBT
 0x3 -> DVBT2
 0x4 -> ISDBT
 0x5 -> DVBS
 0x6 -> ATSC
 0x7 -> J83B
 0xa -> DTMB
 0xb -> DVBS2
 0xf -> DSS
 0x10 -> ATV_PAL
 0x11 -> ATV_SECAM_L_PRIME
 0x12 -> ATV_NTSC
========================== End Broadcast Type List =======================
[../../src/espvr/core/src_v4/data_manager/PVR_Record_Handler.cpp][_BackRecordDataCheck][2032] Not get data from PVR Eng
[../../src/espvr/core/src_v4/data_manager/PVR_Record_Handler.cpp][_BackRecordDataCheck][2032] Not get data from PVR Eng
[../../src/espvr/core/src_v4/data_manager/PVR_Record_Handler.cpp][_BackRecordDataCheck][2032] Not get data from PVR Eng
_ChScan_WaitLock: Timeout!
_ChScan_Tune2RF: 184500KHz
drv_frontend_index = 0 u32BroadcastType = 2
=========================== Broadcast Type List ==========================
 0x0 -> BROADCAST_TYPE_NOT_SEETING
 0x1 -> DVBC
 0x2 -> DVBT
 0x3 -> DVBT2
 0x4 -> ISDBT
 0x5 -> DVBS
 0x6 -> ATSC
 0x7 -> J83B
 0xa -> DTMB
 0xb -> DVBS2
 0xf -> DSS
 0x10 -> ATV_PAL
 0x11 -> ATV_SECAM_L_PRIME
 0x12 -> ATV_NTSC
========================== End Broadcast Type List =======================
[../../src/espvr/core/src_v4/data_manager/PVR_Record_Handler.cpp][_BackRecordDataCheck][2032] Not get data from PVR Eng
[../../src/espvr/core/src_v4/data_manager/PVR_Record_Handler.cpp][_BackRecordDataCheck][2032] Not get data from PVR Eng
[../../src/espvr/core/src_v4/data_manager/PVR_Record_Handler.cpp][_BackRecordDataCheck][2032] Not get data from PVR Eng
Aktualizacja Wiwa Pro New 5.2.1.47:

Kod: Zaznacz cały

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Dec 26 2019 - 17:32:16)  MBOT-1106.0.10.936a0fd.201806111716


DRAM:
Hello U-Boot
Stack Pointer at: 83620740
mem initial, start 0x82CEE180, len 0x402000
SPI:  Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In:    serial
Out:   serial
Err:   serial
[ERROR] do_spi_init_partition:1218: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'

>>>>>>>>>>>>>>>>>>>>Start bootlogo
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showboot.................
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x3A000 0x400
offset 0x3A000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3A028 0x342516; LzmaDec 0x80B00000 0x342516 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
============= set bootargs ===============
Hit any key to stop autoboot:  0
enable dont overwrite function
Boot Check: Reboot by WDT --------
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x35FD000
[USB] Reg 0x28: 0xD000 0x35F
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
USB device specified [0]
USB partition specified [1]
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

1 bytes read
USB device specified [0]
USB partition specified [1]
reading /SbootUpgrade.bin

** Unable to read "/SbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /MbootUpgrade.bin

** Unable to read "/MbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /UrsaUpgrade.bin

** Unable to read "/UrsaUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Current state ->[0x8]
zkc  do_ustar.............
MDrv_FrontPnl_showupgrade.................
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showupgrade.................
USB device specified [0]
USB partition specified [1]
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

1 bytes read
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

16384 bytes read
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

3887128 bytes read
storage is empty
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

>> fatload usb 0 80000000 $(ForceUpgradePath)
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

3887128 bytes read

>> spi_wrc 80004000 0 3b1000
offset 0x0, size 0x3B1000
Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
initialization done!
Erasing...
Writing...
Verifying...

>> setenv usb_complete 1

>> setenv usb_upgrade 0

>> setenv OAD_NEED_UPGRADE 0

>> setenv OAD_TRIGGER_TYPE 0

>> setenv bootcmd ' spi_rdc 0x80b00000 0x3a028 0x32b779; LzmaDec 0x80b00000 0x32b779 0x80000180 0x81000000; go 0x80000224;

>> setenv upgrade_mode null

>> setenv MstarUpgrade_complete 1

>> setenv bl_jpd_read_addr 0x00000000

>> setenv bl_jpd_read_size 0x00000000

>> setenv bl_jpd_write_addr 0x00000000

>> setenv bl_jpd_write_size 0x00000000

>> setenv bl_jpd_inter_addr 0x00000000

>> setenv bl_jpd_inter_size 0x00000000

>> setenv bl_dfb_framebuffer_addr 0x00000000

>> setenv ve_buffer_addr 0x00000000

>> saveenv
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase

>> reset
Reset command is skipped

>> HW2.1.RC20.4.3U
Unknown command 'HW2.1.RC20.4.3U' - try 'help'
[ERROR] do_ustar:737: Error> cmd: HW2.1.RC20.4.3U Fail !!
[ERROR] do_custar:759: Upgrade Application error!
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
AP upgrade OK!~
resetting ...

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Dec 26 2019 - 17:32:16)  MBOT-1106.0.10.936a0fd.201806111716


DRAM:
Hello U-Boot
Stack Pointer at: 83620740
mem initial, start 0x82CEE180, len 0x402000
SPI:  Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In:    serial
Out:   serial
Err:   serial
[ERROR] do_spi_init_partition:1218: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'

>>>>>>>>>>>>>>>>>>>>Start bootlogo
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showboot.................
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x3A000 0x400
offset 0x3A000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3A028 0x32B779; LzmaDec 0x80B00000 0x32B779 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
============= set bootargs ===============
Hit any key to stop autoboot:  0
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
enable dont overwrite function
Boot Check: Reboot by WDT --------
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x35FD000
[USB] Reg 0x28: 0xD000 0x35F
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
USB device specified [0]
USB partition specified [1]
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

1 bytes read
USB device specified [0]
USB partition specified [1]
reading /SbootUpgrade.bin

** Unable to read "/SbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /MbootUpgrade.bin

** Unable to read "/MbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /UrsaUpgrade.bin

** Unable to read "/UrsaUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Current state ->[0x8]
warn!! no upgrade file in usb.
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
usb -

Usage:
usb
offset 0x3A028, size 0x32B779

LZMA Decompression...buf data channge
CRC check success !!
ok
disable interrupts
## Starting application at 0x80000224 ...
1999 drvEMAC_GetMacAddr
cyg_if_attach.225 - After initialize list 0x80691094
IFP: 0x80691084 (eth0)
cyg_if_attach.290 - After inserting 0x8090eda0 into list 0x80691094
IFP: 0x80691084 (eth0)
IFA: 0x8090eda0 - <<0x8090ee1c>>
===> rt_ecos_init()
cyg_if_attach.225 - After initialize list 0x8073f6c8
IFP: 0x8073f6b8 (ra0)
cyg_if_attach.290 - After inserting 0x8090eca0 into list 0x8073f6c8
IFP: 0x8073f6b8 (ra0)
IFA: 0x8090eca0 - <<0x8090ed1c>>
cyg_if_attach.225 - After initialize list 0x809c21d8
IFP: 0x809c21c8 (lo0)
cyg_if_attach.290 - After inserting 0x8090eba0 into list 0x809c21d8
IFP: 0x809c21c8 (lo0)
IFA: 0x8090eba0 - <<0x8090ec1c>>
Register_netisr [2] fun=0x800f6d45

[eCos][CPU INFO] : CPU Clock = 750000000 : RTC Period = 375000
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_DisableInterrupt][3512] MsOS_CPU_DisableInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[MsOS_CPU_RestoreInterrupt][3533] MsOS_CPU_RestoreInterrupt is not supported
[eCos] UtopiaInit

shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
shmem name not found.
[SYS][ERR][AESDMARegisterToUtopia:2323] Not support AESDMA
Flash is detected (0x0D00, 0x5E, 0x40, 0x16)

0046119500d0
Auth OK
[SYS][ERR][SysInit:1761] ###############################################################
[SYS][ERR][SysInit:1762] #       System boot from WDT timeout !!!!!!!!!!!!!!!!!!!      #
[SYS][ERR][SysInit:1763] #       System boot from WDT timeout !!!!!!!!!!!!!!!!!!!      #
[SYS][ERR][SysInit:1764] #       System boot from WDT timeout !!!!!!!!!!!!!!!!!!!      #
[SYS][ERR][SysInit:1765] ###############################################################
 <FWTSP> : RASP from TSIF_RASP
Mstar USB initial, 4 ports sup>> FwVersion:002F2600 , Date:20140924
[FUNC MApi_DB_DFT_GetPCHIntf_CT] [pstIntf  0x80418548]
ported
[NCM] The allocted address is 0xa2f7dfe0
Init Software Timer ok
usbcore: regtered new driver hub
[USB] quirk list init, support max 20
usbcore: regtered new driver usb-storage
[USB] MS USB Host Lib for K5AP only


rtusb init rt2870 --->


usbcore: regtered new driver rt2870
Init chip K5AP, port 0
[USB] constant upll NLib[MApp_CheckFlash][1838] s8SN0 = 1
[App_DTVManger_SetParentCtlPwdStatus][590] DTV Object not created yet
[App_DTVManger_SetParentCtlStatus][557] DTV Object not created yet
, UTMI base 0xbf207500, USBC base 0xbf200e00, UHC base 0xbf204800, USBBC base 0xbf226e00
[USB] init squelch level 0x2
ehci_hcd (CPE_AMBA) at 0x0xbf204800, irq 7
new USB Bus, assigned pBus number 1
pQh: 0xa2f7e000, pQh->qh_dma_addr: 0x02f7e000
periodic frame list aApp_InitBlockData!
[time:951][MApi_DB_CM_InitDTVDataManager:1660]  start!!
[time:955][MApi_DB_CM_PrintAllProgram:6590]     === DTV Programs ===
[time:961][MApi_DB_CM_PrintAllProgram:6597]     === RADIO Programs ===
[time:967][MApi_DB_CM_PrintAllProgram:6604]

[time:971][MApi_DB_CM_PrintAllProgram:6590]     === DTV Programs ===
[time:976][MApi_DB_CM_PrintAllProgram:6597]     === RADIO Programs ===
[time:982][MApi_DB_CM_PrintAllProgram:6604]

[CreatDTVProgramIndexTableAndProgramIDTable,6909] DTV Data Structure is valid

[time:993][FillDTVProgramIndexTableWithOrder:7067]        start!!
[[utopia]]      Start HAL_AUDIO_AllocateVars InitShmFlag=0
create Audio SHM data ...
Audio SHM data is created
reset Audio SHM data ...
[[utopia]][audio]      MStar AUDIO Driver Version : 2.2.3
[[utopia]]      Start HAL_AUDIO_AllocateVars InitShmFlag=1
[[utopia]]      HAL_AUDIO_AllocateVars QUERY ClientCounter=1
[[utopia]]      MDrv_AUDIO_PCM_Init: Init PCM device
rray 0xa2f80000, size 1024
[EHCI] Enable Park Mode: 3
EHCI 1.00, driver eCos Newhost
[root hub] device address 1
USB device manufacturer string (index 3) = MStar eCos 1.0 ehci_hcd
USB device product string (index 2) = CPE_AMBA EHCI
USB device serial number string (index 1) = cpe_ehci
usbdev 1-0 - registering interface 1-0:0
USB hub found
1 port detected

Usb start EX..., pRootHub = 806d2850

[time:1482][check_uid_entryption:1622]  start!!
UT[SYS][ERR][_SysInit_GetColorFMTCMD:1071] fail to get color format failed!!
MDrv_PNL_Init u32PnlRiuBaseAddr = bf200000
MDrv_PNL_Init u32PMRiuBaseAddr = bf000000
[XC,Version] 00709801
 ask EX>> ... porno need to patch
t 0 starting
UTas[time:1514][check_uid_entryption:1627]      u8UIDLength =8
[tik EX>> USB Port 0 is connected
me:1518][check_uid_entryption:1628]     uid_data:
 D5 00 B6 92 12 67 1C 58
[time:1528][check_uid_entryption:1642]  MDrv_FLASH_OTP_Read 0x2000(32) Success!!
 34 29 9E 2F 16 59 0D 56 1B DB 64 73 05 C0 3E 74 D5 77 5D B0 F0 E7 14 6F C6 82 01 FD C9 D9 18 24
[time:1543][check_uid_entryption:1656]  flash_digest:
 34 29 9E 2F 16 59 0D 56 1B DB 64 73 05 C0 3E 74 D5 77 5D B0 F0 E7 14 6F C6 82 01 FD C9 D9 18 24
[time:1556][check_uid_entryption:1659]  sha_digest:
 53 64 A7 D4 FE B9 25 6F 21 D8 4C 4B 2A 54 4D 0B 9A 80 C1 DF 8D 43 32 F8 9E B4 6E D1 CB 8F 28 96
[time:1569][check_uid_entryption:1666]  Check uid entryption failed!
MApi_VectorFont_Init total size=1310720, free size=671440, large size=671428
[xxxx]=====func:MVF_New_Face==line:160======TASKRUN======
[xxxx]=====func:MVF_New_Face==line:243======TASKRUN======

 0
...[MApp_ZUI_API_GetLanguageNum, 107] u8LanguageNum = 8...
stSysSetting.LedDimmer =8
<saved irq> portsc[0x 803], usbcmd[10b09]
hub_port_connect_change ===20180329===> port 1, status 1, change 1
MDrv_HDMITx_EdidChecking::block 0 ==>
0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x10, 0xAC, 0x48, 0xF0, 0x4C, 0x37, 0x54, 0x41,
0x23, 0x18, 0x01, 0x03, 0x80, 0x34, 0x20, 0x78, 0xEA, 0x1D, 0xF5, 0xAE, 0x4F, 0x35, 0xB3, 0x25,
0x0D, 0x50, 0x54, 0xA5, 0x4B, 0x00, 0x81, 0x80, 0xA9, 0x40, 0xD1, 0x00, 0x71, 0x4F, 0x01, 0x01,
0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3C, 0x80, 0xA0, 0x70, 0xB0, 0x23, 0x40, 0x30, 0x20,
0x36, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1A, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x38, 0x34, 0x4B,
0x39, 0x36, 0x34, 0x38, 0x51, 0x41, 0x54, 0x37, 0x4C, 0x0A, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x44,
0x45, 0x4C, 0x4C, 0x20, 0x55, 0x32, 0x34, 0x31, 0x33, 0x0A, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD,
0x00, 0x38, 0x4C, 0x1E, 0x51, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xBD,

MDrv_HDMITx_EdidChecking::Extension Block Number = 1
MDrv_HDMITx_EdidChecking::Block #1
0x02, 0x03, 0x25, 0xF1, 0x50, 0x90, 0x05, 0x04, 0x03, 0x02, 0x07, 0x16, 0x01, 0x1F, 0x12, 0x13,
0x14, 0x20, 0x15, 0x11, 0x06, 0x23, 0x09, 0x1F, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38,
0x2D, 0x83, 0x01, 0x00, 0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45,
0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58,
0x2C, 0x25, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x9E, 0x01, 0x1D, 0x00, 0x72, 0x51, 0xD0, 0x1E,
0x20, 0x6E, 0x28, 0x55, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x8C, 0x0A, 0xD0, 0x8A, 0x20,
0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16,

_MDrv_HDMITx_ParseCEAExtEdid::Short Video Block: 16
_MDrv_HDMITx_ParseCEAExtEdid::Short Audio Block:3
_MDrv_HDMITx_ParseCEAExtEdid::VSDB
Physcal Address = [1, 0, 0, 0]
_MDrv_HDMITx_ParseHdmiVSDB::Support AI = 0 !
_MDrv_HDMITx_ParseDeepColorInfo::Support Color Depth 36-bit
DAC eTiming =6
DAC Panel Table Index =6
[SYS][ERR][_SysInit_GetPanelCMD:1050] fail to get panel failed!!
Wait V Sync!!
[Hal_VE_EnableDI][1841] bEnable = 0, bIsDNR2VE = 0
RootHub SPEED: high-speed
:: Device Speed is 480 Mb/s
new USB device on path usb:1, assigned address 2
pQh: 0xa2f7e060, pQh->qh_dma_addr: 0x02f7e060
usb new device VID = 23a9, PID = ef18
USB device manufacturer string (index 1) = USB
USB device product string (index 2) = DISK
usbdev 1-1 - registering interface 1-1:0
find USB MSC device at device number 2
<saved irq> portsc[0x   d], usbcmd[10b09]
pQh: 0xa2f7e0c0, pQh->qh_dma_addr: 0x02f7e0c0
pQh: 0xa2f7e120, pQh->qh_dma_addr: 0x02f7e120
--> short transfer
Connect USB disk /dev/sdx/, path usb:1
Port device number:7 Lun:0 Id:64
disk_connected.970

read_mbr.659

_parse_mbr_sector.353

_parse_gpt_partition.306

_parse_gpt_partition.315,gpt_sector:2

_parse_gpt_partition,gpt_nr:1,start:2048 ,end:15761470 ,size:15759422
_parse_gpt_partition.340

@@ Host ID 0
LUN 0 is init ok
Removable MSC Lun 0
MSC plug in
[[utopia]]      ===== Check Audio Decoder Protection from hash-key IP =====
[[utopia]]      Hash Key Check DD Fail, no DD license!!
[[utopia]]      Hash Key Check DDP Fail, no DD+ license!!
[[utopia]]      Hash Key Check Dolby MS11 Fail, no Dolby MS11 license!!
[[utopia]]      Hash Key Check Dolby MS12 LC profile Fail, no Dolby MS12 LC profile license!!
[[utopia]]      Hash Key Check Dolby MS12 D profile Fail, no Dolby MS12 C profile license!!
[[utopia]]      Hash Key Check Dolby MS12 B profile Fail, no Dolby MS12 B profile license!!
[[utopia]]      Hash Key Check Dolby Pulse(MS10_DDT) Fail, no Dolby Pulse(MS10_DDT) license!!
[[utopia]]      Hash-key Support Generic HE-AAC!!
[[utopia]]      Hash Key Check DDCO Fail, no DDCO license!!
[[utopia]]      Hash Key Check DTS Fail, no DTS license!!
[[utopia]]      Hash Key Check WMA Fail, no WMA license!!
[[utopia]]      Hash Key Check DRA Fail, no DRA license!!
[[utopia]]      Hash Key Check DTSLBR Fail, no DTSLBR license!!
[[utopia]]      Hash Key Check DTSE Fail, no DTSE license!!
[[utopia]]      Hash Key Check DTSNeoUltra Fail, no DTSNeoUltra license!!
[[utopia]]      Hash Key Check SRS_TSHD Fail, no SRS_TSHD license!!
[[utopia]]      Hash Key Check SRS_THEATERSOUND Fail, no SRS_THEATERSOUND license!!
[[utopia]]      Hash Key Check DTS_StudioSound3D Fail, no DTS_StudioSound3D license!!
[[utopia]]      Hash Key Check COOK Fail, no COOK license!!
[[utopia]]      Hash Key Check DTS_HD Fail, no DTS_HD license!!
[[utopia]]      Hash Key Check Dolby volume Fail, no Dolby volume license!!
[[utopia]]      Hash Key Check SRS_PURESND Fail, no SRS_PURESND license!!
[[utopia]]      ===== Check Protection IP End                         =====
[[utopia]]
 ==========DSP Version Check==================

!!!!!!!!!!![_FirstTaskStart][1616] Driver initial time 3604
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[NMGR][appNetMgr_Init][3089] NMonitor Inited
[NMGR][appNetMgr_Init][3090] NMGR Inited
CVBS ON, RGB OFF, HDMI ON
[NMGR][appNetMgr_LoadLinkType][2697] LINK TYPE>>> WLAN
iwpriv ra0 set RadioOn=1
[NMGR][_CheckNetworkStatus_WLAN][1540] NET_STATE_DEVICE_NOTREADY
[msCHIP_DAC_SetOutputSource][156] input bitmap: 0x00000011
CVBS on
SVIDEO off, YPBPR off, RGB on
SCART on
[time:3711][_SetHDMI:394]       audioType =7  eHDMIType=1
[time:3803][_SetDeviceMute:508] bMute = 0
[msAPI_XC_ReMapComponentType][440]: msAPI_XC eTiming = 6
[Hal_VE_EnableDI][1841] bEnable = 0, bIsDNR2VE = 0
[App_DTVManger_CreateObject][217] create DTV object success (1).
[ZUI] init: sz_msg_q=6216
Decompress_bmp_data_size = 547360
MDrv_HDMITx_EdidChecking::block 0 ==>
0x00, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0xFF, 0x00, 0x10, 0xAC, 0x48, 0xF0, 0x4C, 0x37, 0x54, 0x41,
0x23, 0x18, 0x01, 0x03, 0x80, 0x34, 0x20, 0x78, 0xEA, 0x1D, 0xF5, 0xAE, 0x4F, 0x35, 0xB3, 0x25,
0x0D, 0x50, 0x54, 0xA5, 0x4B, 0x00, 0x81, 0x80, 0xA9, 0x40, 0xD1, 0x00, 0x71, 0x4F, 0x01, 0x01,
0x01, 0x01, 0x01, 0x01, 0x01, 0x01, 0x28, 0x3C, 0x80, 0xA0, 0x70, 0xB0, 0x23, 0x40, 0x30, 0x20,
0x36, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1A, 0x00, 0x00, 0x00, 0xFF, 0x00, 0x38, 0x34, 0x4B,
0x39, 0x36, 0x34, 0x38, 0x51, 0x41, 0x54, 0x37, 0x4C, 0x0A, 0x00, 0x00, 0x00, 0xFC, 0x00, 0x44,
0x45, 0x4C, 0x4C, 0x20, 0x55, 0x32, 0x34, 0x31, 0x33, 0x0A, 0x20, 0x20, 0x00, 0x00, 0x00, 0xFD,
0x00, 0x38, 0x4C, 0x1E, 0x51, 0x11, 0x00, 0x0A, 0x20, 0x20, 0x20, 0x20, 0x20, 0x20, 0x01, 0xBD,

MDrv_HDMITx_EdidChecking::Extension Block Number = 1
MDrv_HDMITx_EdidChecking::Block #1
0x02, 0x03, 0x25, 0xF1, 0x50, 0x90, 0x05, 0x04, 0x03, 0x02, 0x07, 0x16, 0x01, 0x1F, 0x12, 0x13,
0x14, 0x20, 0x15, 0x11, 0x06, 0x23, 0x09, 0x1F, 0x07, 0x67, 0x03, 0x0C, 0x00, 0x10, 0x00, 0x38,
0x2D, 0x83, 0x01, 0x00, 0x00, 0x02, 0x3A, 0x80, 0x18, 0x71, 0x38, 0x2D, 0x40, 0x58, 0x2C, 0x45,
0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x01, 0x1D, 0x80, 0x18, 0x71, 0x1C, 0x16, 0x20, 0x58,
0x2C, 0x25, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x9E, 0x01, 0x1D, 0x00, 0x72, 0x51, 0xD0, 0x1E,
0x20, 0x6E, 0x28, 0x55, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x1E, 0x8C, 0x0A, 0xD0, 0x8A, 0x20,
0xE0, 0x2D, 0x10, 0x10, 0x3E, 0x96, 0x00, 0x06, 0x44, 0x21, 0x00, 0x00, 0x18, 0x00, 0x00, 0x00,
0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x16,

_MDrv_HDMITx_ParseCEAExtEdid::Short Video Block: 16
_MDrv_HDMITx_ParseCEAExtEdid::Short Audio Block:3
_MDrv_HDMITx_ParseCEAExtEdid::VSDB
Physcal Address = [1, 0, 0, 0]
_MDrv_HDMITx_ParseHdmiVSDB::Support AI = 0 !
_MDrv_HDMITx_ParseDeepColorInfo::Support Color Depth 36-bit
ubSYNSet=253c82, dSYNCLK=928, dSSC_Span=773, dSSC_Step=3
dPixel_Clk=74
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[FE][ERR][MApi_FEM_GetAvailableFEResource:449] Obtain s32_FEM_ResourceMutex failed.
[FE][ERR][MApi_FEM_GetFEType:419] INVALID_FEM_HANDLER
[FE][ERR][_FEM_GetFEConfigByHandler:1237] Invalid handler !
[FE][ERR][MApi_FEM_Tune2RfCh:634] Wrong Handler
[time:4699][appMain_GetWakeupType:1617] MDrv_PM_GetWakeupSource = 0
[time:4705][_GetWakeupType:1490]        Start!
[time:4708][_GetWakeupType:1556]        return 0
[time:4699][MApi_DateTime_Init:485]     appMain_GetWakeupType()=0
[time:4718][appMain_GetWakeupType:1617] MDrv_PM_GetWakeupSource = 0
[time:4724][_GetWakeupType:1490]        Start!
[time:4727][_GetWakeupType:1556]        return 0
[_SI_MutexLock][350] Err: SI mutex does not exsit!
MApi_EpgDB_SetExtendedEventPoolSize 0x4e0000
[EPGDB][000812]  =========================================================================
[EPGDB][000813]  _pu8EitBufMask:        (Start, End, Length)= (0xa2ef8580, 0xa2ef8585, 0x00000005)
[EPGDB][000814]  _pMapBufIdxTable:      (Start, End, Length)= (0xa2eae660, 0xa2eae7f0, 0x00000190)
[EPGDB][000815]  _pu8EpgDbEvtMask       (Start, End, Length)= (0xa2ef8300, 0xa2ef8571, 0x00000271)
[EPGDB][000816]  _pu8EpgDbScheHdrList   (Start, End, Length)= (0xa2ef77b0, 0xa2ef82f0, 0x00000b40)
[EPGDB][000817]  _pu8EpgDbSrvEvtList    (Start, End, Length)= (0xa2eeda20, 0xa2ef77a0, 0x00009d80)
[EPGDB][000818]  _pu8EpgDbSrvSecList    (Start, End, Length)= (0xa2ed9a10, 0xa2eeda10, 0x00014000)
[EPGDB][000819]  _pu8EpgDbEvtHdrList    (Start, End, Length)= (0xa2eb2900, 0xa2ed9a00, 0x00027100)
[EPGDB][000820]  _pu8EpgDbPfHdrList     (Start, End, Length)= (0xa2eb2820, 0xa2eb28e8, 0x000000c8)
[EPGDB][000821]  _pu8EpgDbPfPresent     (Start, End, Length)= (0xa2eb0810, 0xa2eb2810, 0x00002000)
[EPGDB][000822]  _pu8EpgDbPfFollow      (Start, End, Length)= (0xa2eae800, 0xa2eb0800, 0x00002000)
[EPGDB][000827]  EPG database allocate 0x00529e8e bytes
[EPGDB][000833]  =========================================================================
MApi_EpgDB_Clear : Reset eit buffer
[-]MApi_EpgDB_Init


 DTV version: hello
 BSP version: hello
 DDI_MISC version: hello
 OTT version: hello
[time:4867][check_uid_entryption:1622]  start!!
[time:4874][check_uid_entryption:1627]  u8UIDLength =8
[time:4879][check_uid_entryption:1628]  uid_data:
 D5 00 B6 92 12 67 1C 58
[time:4885][check_uid_entryption:1642]  MDrv_FLASH_OTP_Read 0x2000(32) Success!!
 34 29 9E 2F 16 59 0D 56 1B DB 64 73 05 C0 3E 74 D5 77 5D B0 F0 E7 14 6F C6 82 01 FD C9 D9 18 24
[time:4901][check_uid_entryption:1656]  flash_digest:
 34 29 9E 2F 16 59 0D 56 1B DB 64 73 05 C0 3E 74 D5 77 5D B0 F0 E7 14 6F C6 82 01 FD C9 D9 18 24
[time:4914][check_uid_entryption:1659]  sha_digest:
 [MWPVR] Not Initialize PVR!
SetFileEndAutoResume => 1
[MApi_PVR_Configure][3202]: Program Change Auto mode !!
53 64 A7 D4 FE B9 25 6F 21 D8 4C 4B 2A 54 4D 0B 9A 80 C1 DF 8D 43 32 F8 9E B4 6E D1 CB 8F 28 96
[time:4937][check_uid_entryption:1666]  Check uid entryption failed!
[GOP_GWIN_Is32FBExist][5728]FbId 255  is out of range
leave MApp_ZUI_API_InitCanvasGDI -> MApp_ZUI_API_GetFontMVF in 131
[GOP_GWIN_Is32FBExist][5728]FbId 255  is out of range
[MApp_ZUI_ACT_TerminateMainMenu][7072]
[MApp_SaveGenSetting][2022]
 Get timeout_ms = 0
[time:5985][_DisappearAllPopupMsg:589]  start!
[_SI_MutexLock][350] Err: SI mutex does not exsit!
[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[FE][ERR][MApi_FEM_Get_FE_InitStatus:815] Frontend Manager isn't inited[ZAPPER][ERR][_Zapper_Signal:4656] Tuner not init yet
[FE][ERR][MApi_FEM_GetAvailableFEResource:449] Obtain s32_FEM_ResourceMutex failed.
[FE][ERR][MApi_FEM_GetFEType:419] INVALID_FEM_HANDLER
[FE][ERR][_FEM_GetFEConfigByHandler:1237] Invalid handler !
[FE][ERR][MApi_FEM_SetDTVFE:854] Wrong Handler
[FE][ERR][MApi_FEM_GetFEType:419] INVALID_FEM_HANDLER
[FE][ERR][_FEM_GetFEConfigByHandler:1237] Invalid handler !
[FE][ERR][MApi_FEM_Tune2RfCh:634] Wrong Handler
Naciśnięte menu:

Kod: Zaznacz cały

[time:114735][MApp_ZUI_ACT_HandleTVBannerKey:5212]      key = 15 appPvr_IsPlay()=0
[time:114742][MApp_ZUI_ACT_HandleTVBannerKey:5323]      2222  key = 15
Wyszukiwanie kanałów rozpoczęte
Czarny ekran przez kilka sekund:

Kod: Zaznacz cały

Current Braodcast Type [0]
[MApp_ZUI_ACT_TerminateMainMenu][7072]
[MApp_SaveGenSetting][2022]
[ERROR] Can't get Correct Scan table, FE type[0]
Max Channel = 70
Min Channel = 5
 === [MApp_MenuChannel_FullScan_Start]==== Start FQ = 177500 , End FQ = 866000

 ================== scanParam.bScanMode[1]
[FE][ERR][MApi_FEM_GetFEhandler:921] There is no FE in status [1]
Restart

Kod: Zaznacz cały

BOOTSPI
BIST0_OK
_OK!decomp
_done
done
[AT][MB][start ub][0]

U-Boot 2011.06 (Dec 26 2019 - 17:32:16)  MBOT-1106.0.10.936a0fd.201806111716


DRAM:
Hello U-Boot
Stack Pointer at: 83620740
mem initial, start 0x82CEE180, len 0x402000
SPI:  Flash is detected (0x09A0, 0x5E, 0x40, 0x16)
uboot held at [8F000000~90000000]
Now running in RAM - U-Boot at: 830F0180
In:    serial
Out:   serial
Err:   serial
[ERROR] do_spi_init_partition:1218: This function doesn't support
============= set bootargs ===============
Unknown command 'panel_pre_init' - try 'help'

>>>>>>>>>>>>>>>>>>>>Start bootlogo
[AT][MB][JPD Decode][0]
MDrv_FrontPnl_showboot.................
spi_rdc 0x80B00000 0xB000 0x400
offset 0xB000, size 0x400
spi_rdc 0x80B00000 0x3A000 0x400
offset 0x3A000, size 0x400
setenv bootcmd ' usb exit;spi_rdc 0x80B00000 0x3A028 0x32B779; LzmaDec 0x80B00000 0x32B779 0x80000180 0x81000000; go 0x80000224;
Saving Environment to SPI Flash...
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
============= set bootargs ===============
Hit any key to stop autoboot:  0
enable dont overwrite function
Boot Check: Reboot by WDT --------
AC on
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Check USB port[0]:
[USB] usb_lowlevel_init++
[USB] USB EHCI LIB VER: 2017.08.11-k5ap
[USB] Port 0 is Enabled
[USB] TV_usb_init (UTMI Init) ++
[USB] UTMI Base BF207500
[USB] UHC Base BF204800
[USB] USBC Base BF200E00
[USB] BC Base BF226E00
[USB] init squelch level 0x2
[USB] TV_usb_init--
[USB] Usb_host_Init++
[USB] Async base addr: 0x35FD000
[USB] Reg 0x28: 0xD000 0x35F
[USB] disable run
[USB] Host Speed:2
[USB] enable aynch
[USB] Usb_host_Init--
[USB] usb_lowlevel_init--
scanning bus for devices... [USB] control1 max:40

[USB] interface[0] conf:1 value 8:
1 USB Device(s) found
       scanning bus for storage devices... [USB] no_of_ep: 2
[USB] find bulk ep: 0
[USB] find bulk ep2: 1

[USB] bulk max packet size: ep(out) 0x200, ep2(in) 0x200
[USB] bulk0 is out
max lun:0
1 Storage Device(s) found
USB device specified [0]
USB partition specified [1]
reading upgrade_7T10E_HW2.1.RC20.4.3U_WIWA_PRO_V5.2.1.47_RC001.bin

1 bytes read
USB device specified [0]
USB partition specified [1]
reading /SbootUpgrade.bin

** Unable to read "/SbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /MbootUpgrade.bin

** Unable to read "/MbootUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /UrsaUpgrade.bin

** Unable to read "/UrsaUpgrade.bin" from usb 0:1 **
USB device specified [0]
USB partition specified [1]
reading /ForceUpgradeApp.bin

** Unable to read "/ForceUpgradeApp.bin" from usb 0:1 **
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
Current state ->[0x8]
warn!! no upgrade file in usb.
Write addr=0x003FE000, size=0x00001000
sector erase
Write addr=0x003FF000, size=0x00001000
sector erase
usb -

Usage:
usb
offset 0x3A028, size 0x32B779

LZMA Decompression...buf data channge
CRC check success !!
ok

ukaszu
Posty: 73
Rejestracja: 15 września 2022, o 10:55
Miejscowość: Zalesie

Re: Modyfikacja firmware STB DIPOL SIGNAL T2 - przystosowanie pilota WIWA - crossflash STB WIWA

Post autor: ukaszu »

Dziękuję za logi @gocom :) Jeszcze się tylko upewnię (bo nie widzę tego w logach UART) - czy po wgraniu i resecie (przytrzymanie przycisku INFO) zachowuje się tak samo? Te błędy wyglądają naprawdę interesująco, muszę sobie sprawić taki stary sprzęt i samemu zobaczyć (aktualnie mam do testów tylko nowego MAXXa).

Zygzuś pisze: 4 października 2022, o 15:22 Tak, na pilotach wiwy nie ma, a obsługuje np. Folder w górę czy zmianę nazwy kanału. Na pilocie wiwy robił to inny przycisk.
Który to przycisk?

Zablokowany